Always thoroughly clean the spray gun after each use. to clean the spray gun: 1. spray a small amount of cleaning solvent through the gun. note: Check with local laws regarding this practice. If you are spraying on a regular basis, spraying solvents into the air may be illegal. A cabinet style spray gun cleaner may be required. 2. disConneCt sprAy gun FroM Air! 3. remove the cup and cup lid, then disassemble the gun by unscrewing the fluid control knob and removing the spring and needle (see fig

Do not approved garment. smoke in the spraying area or when 16. INAPPROPRIATE USE. DO NOT spraying. point or shoot spray gun directly 9. FIRE EXTINGUISHERS. Always at yourself or another person or animals. Do not attempt to use the spray gun for any other use than it have a fully charged multi-class or class B fire extinguisher in the was intended. immediate area. 17. STORAGE. Thoroughly clean and 10. AVOID UNINTENTIONAL dry spray gun before storage. Store OPERATION. Always disconnect air in an

1 F A E J I B C D G H K Figure 1. Model H8225 Inventory. Model H8225 21.2 Gallon Paint Tank with Gun -5 Tank Assembly Regulator Assembly Fluid Outlet Adapter Lift Handle Pressure Gauge Air Inlet Fitting Safety Valve Air Outlet Fitting Figure 2. Regulator and lift handle installed on paint tank. To assemble the paint tank: 6. Connect the material hose to the fluid outlet adapter on the tank lid. 1. Apply Teflon tape to all male pipe threads. 7. Install a pressure regulator (not includ- Figure " y

Figure 2. Installing filter. 2.Attach the cup to the gun body as shown in Figure 3. Figure 3. Cup installed. Gun Body Cup Connection Point Air Fitting BA C D E Figure 1.Inventory components shipped with Model H8224. -4- Model H8224 HVLP Spray Gun 3. Install and tighten the barbed hose fitting to the air inlet with the provided nut; or attach a female 1.4" NPT quick connect fitting (not included) to the air inlet for connection to an air coupler. Note: Using a 1.4" NPT quick disconnect set-up, wi

Stage two sprays material. 6. Cup: Holds material; includes a vented cap. -10- Model H8115/H8117 Spray Gun SECTION 4: OPERATIONS ADANGER 4 EXPLOSION HAZARD! DO NOT smoke or have any source of flame or spark near spraying. Vapors will explode if ignited. ▲WARNING RESPIRATORY HAZARD! Always use respirator rated for organic vapor and solvent use when using spray equipment. Failure to protect your lungs can lead to respiratory illness and nervous system damage. ▲WARNING TOXIC FUMES! Alway

150 PSI maximum air pressure. 1.4" NPT. Figure 6. G6261 Campbell Hausfeld™ water filter. G8114—3.8" x 25 Ft. Air Hose G8115—3.8" x 50 Ft. Air Hose G8116—3.8" x 100 Ft. Air Hose Multi-purpose red rubber air hose is flexible and abrasion resistant. Rated for 200 PSI, this air hose has a bursting strength of 800 PSI and 1.4" NPT ends. Figure 7. Red rubber air hose. H7274—Campbell Hausfeld™ Pressure Regulator Provides regulated output pressure of 0 to 125 PSI for proper tool operation. Locking press

parts. Non-slip footwear is recom-20. CHECK DAMAGED PARTS. mended. Wear a protective hair cov-Before further use of the tool, a ering to contain long hair. guard or other part that is dam 12. ALWAYS USE SAFETY GLASSES. aged should be carefully checked Also use a face or dust mask if cut-to determine that it will operate ting operation is dusty. Everyday properly and perform its intended eyeglasses only have impact resis-function. Check for alignment of tant lenses, they are NOT safety moving par

Overloading can cause the jack to collapse and drop the load. 2. ALWAYS support the vehicle with appropriately rated support stands before working under it. 3. DO NOT attempt to move the vehicle while the jack is in use. 4. Use only on hard level surfaces like concrete or asphalt. Other surfaces are potentially unstable. 5. Center the load on the jack to maintain proper balance and stability. 6. DO NOT use jack if it begins leaking fluid or if it slowly sinks with a heavy load. These are in

Spray so the material wets out nicely without running or sagging. 8. Use the pattern control knob to adjust the spray fan to your desired pattern. 9. Keep the gun tip perpendicular, parallel and 6-8" from the work at all times when spraying as shown in Figure 4. Do not allow your wrist to bend. This will cause the gun to arc across the surface and distribute the material unevenly, possibly creating sags and dry spots. 10. Begin spraying 2-3 inches before the work and continue to the end of the w