Fit the strap hooks into the round holes at the top of the Spray Pack. ii. Feed the strap through the vertical slots at the bottom of the Spray Pack, loop around and feed back through the strap buckle. Spraying IT IS RECOMMENDED THAT THE UNIT IS TESTED WITH WATER PRIOR TO EACH USE 1. Remove Spray Pack Lid (2) and pour in required spray material and thinners. 2. Ensure the spray material and thinners do not exceed the max fill line on the Spray Pack. 3. Fit the Spray Pack Lid, ensuring that Seal

Refer to the chapter on cleaning to see how the Fluid Tip and Fluid Needle can be removed and switched for a smaller/larger Fluid Tip and Fluid Needle assembly. • Fill the Paint Container with the product to be sprayed. Stir well (as mentioned above). • Screw the Paint Container to the base of the Spray Gun and tighten accordingly. • Unroll the motor unit air hose and attach it to the back of the Spray Gun. • Unroll the power cable and attach the plug to the mains supply. • Switch the Spray Stat

• Always have a drop cloth and wear a mask like you would for a roller or brush if spraying inside. • Practice your technique (even if you have sprayed before), just to familiarize yourself with the coating and different spray patterns and flow rate of the gun. • Spend a few minutes getting the viscosity of the paint where it needs to be. • Always clean up your Spray Gun after every use. PLEASE READ MAIN INSTRUCTION MANUAL BEFORE USE Basic Rules of Spraying Follow these simple instructions to se

Please retain for future reference SAFETY OPERATING INSTRUCTIONS PLEASE READ BEFORE USE . ALWAYS CHECK PAINT MANUFACTURERS THINNING INSTRUCTIONS BEFORE PROCEEDING. . ALWAYS CHECK PAINT MANUFACTURER’S INSTRUCTIONS FOR SURFACE PREPARATION. . ENSURE PAINT IS STIRRED THOROUGHLY BEFORE USE. . Never use corroded or damaged batteries, do not mix old and new batteries. . Do not overfill the paint reservoir. . NEVER use any liquids other than those specified. . Always ensure motor housing is firmly clipp

Earlex Ltd will accept no responsibility for the use of this product if usedfor any other purposes than those detailed herein. SAFETY OPERATING INSTRUCTIONS WARNING: When using the Paint Sprayer, basic safety precautions, including the following, should always be followed t< reduce the risk of fire, electric shock and personal injury ! Keep work area clean -Cluttered areas and benches invite injuries. ! Consider work area environment -Do not expose the spray gun to rain. Do not use the spray gun

No obstante, algunos materiales no pueden pulverizarse, asi que revise las recomendaciones del fabricante antes de comprar la pintura. Si el material es solo para ser aplicado con brocha, normalmente no puede ser pulverizado. ESTA UNIDAD NO PUEDE USARSE CON PINTURAS CON TEXTURA. EL USO DE DICHOS MATERIALES CAUSARA EL DETERIORO PREMATURO, QUE INVALIDARA LA GARANTIA. PARA OBTENER LOS MEJORES RESULTADOS DE SU SISTEMA DE PINTADO AEROGRAFICO, LE ROGAMOS LEA DETENIDAMENTE LAS INSTRUCCIONES ANTES DE US

The round spray is used for small objects or for areas - such as corners – that are difficult to reach. To adjust the spray pattern, loosen the Air Cap Ring (1), adjust the position of the Air Cap (2) to obtain either a vertical, horizontal or round pattern then re-tighten the aircap ring. PAINT VOLUME The volume of paint sprayed is easily adjustable. (Fig.5(a)) Completely close Fluid Adjusting Screw (8) by turning this clockwise as far as it will go. Whilst pulling the trigger, begin turning th

BEFORE USE - PLEASE READ THE SAFETY & OPERATING INSTRUCTIONS. Please retain for future reference N0150 05/05.qxd 27/5/05 10:28 am Page 2 SAFETY INSTRUCTIONS WARNING! FIRE AND EXPLOSION HAZARD. . CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, USE INDOORS ONLY. . The substances used with this spray applicator (paint, thinners etc) may contain hazardous, harmful, explosive or corrosive materials. ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS ISSUED WITH THIS PRODUCT AND THE MATERIAL BEING US

The spray applicator should be thoroughly cleaned after each use. Follow the cleaning instructions on page 9 with reference to the drawings on page 3 ! Check the needle and fluid tip on a regular basis for excessive wear, and replace as necessary. See the cleaning instructions for the correct procedure for removing these parts. Replacement needle sets are available from Earlex Ltd. ! Keep all moving parts lubricated with a light smear of petroleum jelly. ! Lubricate the gland washer, after each

mostrado en LISTA DE PIEZAS N° Description 1. Anillo del soporte de la boquilla 2. Soporte de la boquilla de aire 3. Placa del distribuidor de aire 4. Boquilla de 2.0mm 5. Sello de la boquilla 6. Tornillo pivote 7. Arandela 8. Ensamblaje del cuerpo principal 9. Aguja del fluido de 2.0mm 10. Adaptador 11. Muelle 12. Tornillo de ajuste 13. Pivote 14. Tubo de alimentaci n de aire 15. Tuerca del prensaestopas LISTA DE PIEZAS N. pieza L0151 L0152 L0162 L0157 L0159 L0179 L0195 L0180 L0166 L0174 L0175