Indica una situacion potencialmente peligrosa, la cual, si no es evitada, podria resultar en lesiones menores o m o d e - r a d a s . Usado sin el simbolo de seguridad de alerta indica una situa-cion potencialmente riesgosa la que, si no es evitada, podria causar danos en la pro p i e d a d . PROPOSICION DE CALIFORNIA 65 Algunas particulas originadas al lijar, aserrar, amolar, taladrar y realizar otras actividades de construccion contienen productos quimicos que producen cancer, defectos de naci

HERRAMIENTAS DE ENSAMBLAJE REQUERIDAS 1/8" Llave Inglesa Hexagonal (suministro) El Destornillador de Phillips 6 Mm Llave Inglesa Hexagonal (suministro) la Llave Inglesa Ajustable ESTIMACION DEL TIEMPO DE ENSAMBLAJE Menos de 1 hora AJUSTANDO LA TENSION DE CORREA Su lijadora se envia de fabrica con la correa de marcha (A) Fig. 2 ensamblada a ambas poleas (B) y (C). Antes de ensamblar la unidad de disco a la maquina, revise y ajuste la tension de correa: 1. Afloje el tornillo (D) Fig. 1 con la 6 Mm

IMPORTANT: Securely position the sanding disc on the disc assembly prior to applying power to the tool. AB C Fig. 9 Fig. 10 Fig. 11 ATTACHING DISC TABLE Fig. 12 A B C D D E E C A B Fig. 13ADISCONNECT MACHINE FROM POWER SOURCE. 1. Thread the disc table trunnion stud (A) Fig. 12 into the hole (B) on the side of the machine and tighten snug. 2. Place the disc table trunnion clamp (C) on the stud and insert the two pins (D) in the two holes (E). 3. Attach the washer, spring, and knob (Inset - Fig. 1

33 for use with a dust collection system. You must adjust the shield to suit your sanding operation. 1. If you are sanding with the disc, push in on the dust shield (A) Fig. 33. A Fig. 33 14 2. If you are sanding with the belt, pull the dust shield (A) Fig. 34 outward. A Fig. 34 WRENCH STORAGE A hole is provided in the stand for storing the hex wrench (A) Fig. 35, supplied with the sander. REMOVING UPPER SANDING A Fig. 35 DRUM GUARD You can remove the upper sanding drum guard (A) Fig. 36 to sand

416-01-651-0001 Dated 10-20-78 31-200 8V2" DISC SANDER The 81/a" Disc Sander permits straight, angular, curved and convex surfaces to be finished accurately. For circular, band and scroll sawed work, beveling edges and ends of square stock and rounding corners, it is ideal. It can be used for finishing wood, plastics, non-metals and metals in the home workshop. TILTING THE TABLE The table of disc sander can be tilted 45 degrees down and 30 degrees up. To make this adjustment, 'loosen the han

We suggest wiping any FI®» 1 excessive leakage of oil from the sides of the base casting to avoid the possibility of any grit entering the porous bronze bushings. OPTIONAL MOTORS N®, '■ HJP. Hearings Speed Volts 82-133 % Sleeve 1725 115 62-134 _ % Ball 1725 115 62-142 m Ball 1725 115 ACCESSORIES Miter Gauge No. 31-304 For use with 31 -200 81## 'Disc Sander. Sanding Discs No. 46-101 Coarse (40 grit) No. 46-102 Medium (80 grit) Pkg. of 12, 8%" diameter, garnet. Requires disc adhesive

22, is located on the sander base. To turn the sander “ON” move the switch up to the “ON” position. To turn the sander “OFF” move the switch down to the “OFF” position. A Fig. 22 11 LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) Fig. 23, and pulling it out of the switch as shown. With the switch toggle (B) removed, the switch will not

3. Loosen set screw (F) Fig. 34, and insert support bar (E) and table assembly (B) into hole (G) Figs. 33 & 34, on belt unit. Tighten set screw (F) to hold support bar and table assembly in position. WARNING: THE TABLE EDGE (H) FIG. 34, MUST BE POSITIONED A MAXIMUM OF 1/16" AWAY FROM SANDING BELT (J) TO AVOID TRAPPING THE WORK OR FINGERS BETWEEN THE TABLE AND SANDING BELT. Fig. 33 A C B D E G Fig. 34 B F G E H J DUST SPOUT A dust spout (A) Fig. 35, is supplied with your sander and can easily be

La exposicion al polvo puede causar lesiones respiratorias graves y permanentes u otras lesiones graves y permanentes, incluyendo silicosis (una enfermedad pulmonar grave), cancer y muerte. Evite aspirar el polvo y evite el contacto prolongado con el polvo. Si se permite que el polvo entre en la boca o en los ojos, o que se deposite en la piel, se puede promover la absorcion de material nocivo. Use siempre proteccion respiratoria aprobada por NIOSH/OSHA que se ajuste apropiadamente y sea adecuad

10-24x3/8" Pan Head Screw (2) 10. M8.4 Flat Washer (1) 11. 3/16" Flat Washer (2) Fig. 1 1 2 3 4 5 6 7 8 9 12 13 5 ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. BELT SANDER TABLE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Locate the M8x1.25x30mm hex head screw (A) Fig. 2, M8.4 flat washer (B), and table locking handle assembly (C), (D), (E) and (F). NOTE: T