4.All the buttons except the sleeping button is no effective after wire controller received lock signal fromremote controller. 6 functions fo non-negative ion unit. 8 12 17 19 20 24 25 26 30 3 23 D Remote LCD display contents and key name and each key function introduction TEMP HEALTH FAN MODE SWING TIMER ON OFF LOCKRESETCODE OFF H AUTO ion 6 4 2 7 8 9 10 12 13 14 15 16 17 18 19 11 20 21 B A 1.ON/OFF button Used to turn on/off unit 2.Temperature Setting button Used to set temperature, temperatur

A separate power circuit shall be supplied and connected by a qualified electrician according to the wiring rules specified in the corresponding national standard. A current leakage breaker must be installed. The connection method of power cord is " Y " type. If the power flexible cord is damaged, it shall be replaced by the manufacturer or its service department or similar qualified technician so as to avoid risks. Power cord plug: L should be connected to the live wire, N should be connected t

Just press TIMER button several times until TIMER mode disappears. According to the Time setting sequence of TIMER ON or TIMER OFF, either Start-Stop or Stop-Start can be achieved. 14 Operating Instructions Sleep Function At night, before going to bed you can press down the SLEEP button on the controller and the air- conditioner will run by the comfortable sleeping mode to make you sleep more comfortable. Comfortable Sleep SWING SET LOCKRESET HEALTH MODE SLEEP CLOCK TIMER ON OFF * MODE FAN HEALT

The power supply to the indoor unit shall be laid in complying with the operational instruction manual. The electric wiring shall avoid contacting with the high temperature part of the piping so as to prevent the cable insulation melts and cause dangers. After connected on the terminal block, the wires shall be bent to U form and then fastened with wire clip. The control wiring and refrigerant piping may be laid and fastened together. Before completion of vacuum pumping of the refrigerant pipe s

Lower cover of wire controller Switch button 2. Install the wired remote controller Please drill two holes on the wall according to the back cover screw hole position of the wire remote controller, then strike the wood block to the holes respectively, then align the 2 screw hole of the wire controller back cover to the wood block, fasten the wire reote controller to the wall use wood screws. 3. Switch setting The switchs setting as follows:1.ON 2.OFF 3.ON 4.OFF Note Try as far as possible a flat

DO NOT install the machine in place where flammable gasreleases easily to avoid firehazard. ! Ensure electric leakage breakerbeing installed. Electric leakage breaker MUST be installed, otherwise electric shock may becaused. If the power supply cord isdamaged, call a certifiedelectrician of the manufacturer or other maintenance departmentto replace it. ! 10 Important Points of Safety Attention Attention points for use * Ensure ventilation of the room if the machine is used with burning facilitie

1 Cautions 2 Cooling Heating Indoor outdoor Rated Maximum Minimum 27 32 18 19 23 14 35 43 -5 24 26 -- 20 27 15 14.5 -- -- 7 24 -15 6 18 -- DB C WB C DB C WB C Indoor outdoor DB C WB C DB C WB C Cautions D AE072FCAKA AE242FCAKA AE092FCAKA , AE122FCAKA , AE142FCAKA , AE182FCAKA , AE212FCAKA have the Return air box (see the following picture) when shipping from the factory and they are back-side return air. During the installation, also can be changed to Down-side Return air according to the user's

Please wait for 3 min. 18 Trouble Shooting During DRY operation, there is no air sent out or fan speed cant be changed. In HEAT mode, the outdoor unit generates water or steam. This occurs during removal of the frost (in defrosting operation) on the radiator of outdoor unit. Defrost operation In HEAT mode, the indoor fan still keeps running even the unit operation stops. After the unit stops, the indoor fan will continue to run for a while to eliminate residual heat. Before asking for after-serv