Never perform any maintenance or assembly procedures on this machine while the engine is running. 1. Place the blower upright on the ground or on a sturdy work surface. 2. Push the wide sweeper nozzle (5) over the straight tube (4) lining up the locking pins. 3. Rotate the nozzle tube clockwise locking it into place. 4. Push the assembled blower tube over the discharge port (17). 5. With the locking pins lined up, rotate the straight tube (4) clockwise to lock it into position. Before Use IMPORT

• Do not run the engine in an enclosed and/or poorly ventilated area. The gas of the engine contains carbon monoxide, which is dangerous to your health. • Work only when there is sufficient light. • Do not use the blower when it is raining or when the grass is wet. • Caution must be taken while blowing on slopes. • Turn off the engine if you must leave the blower unattended. • Never change the rated speed of the engine in any way. • Stop the engine and remove the spark plug cover in these cases:

If fuel must be stored longer than 30 days, it should first be treated with a stabilizer or similar product. Operation Choke control If the engine is cold you will need to use the choke control. Start position (choke closed). Run position (choke open). Starting the blower To start the engine, proceed as follows: 1. Press the primer (9) 5 to 6 times until there are no air bubbles are visible in the fuel discharge line. Note. This is not necessary if the engine is warm. 2. If the engine is cold, m

Battery charging 1. Connect charger (5) to power source. The green light (a), should light up. This indicates the charger is ready to begin charging. 2. Position battery pack on charger, align rails (d), on battery charger with (e) on battery pack. Slide battery forward onto charger until it clicks into position. 3. The red light (b), should begin to glow continuously, indicating that the battery pack is receiving a “Fast Charge”. 4. After approximately one hour, the “Fast Charge” indicator red

To fit the shoulder strap (11), simply open the buckle on the strap and fit it through the hole provided on the housing of the blower/vac. Operation of the blower vac Prior to using the blower vac, ensure you have read and understood this instruction manual. Ensure you are wearing suitable clothing and also safety equipment like safety glasses, ear protection and a mask if necessary. Ensure the attachments to the blower vac are correctly fitted and adjusted. Be aware of other people and animals

• Do not operate this appliance with long loose hair or loose fitting jewellery. Tie long loose hair back and remove loose fitting jewellery. • Do not allow the garden vac to pick up any burning or smouldering materials like ashes, cigarette butts etc. • Do not attempt to pick up breakable objects like glass, plastics, china etc. • Do not use in vacuum operation without the collection bag fitted. • Do not use the garden vac on gravel surfaces. • Only operate the tool during broad daylight or wit

• The operator is responsible for accidents or hazards occuring to other people or their property. • Do not handle the plug or the tool with wet hands and do not use the tool in the rain. • Use only outdoor rated extension leads that are so marked. Keep the extension cord away from heat, oil and sharp edges. • Ensure that the extension lead is secured in a manner that prevents it form disconnecting from the plug whilst in use. • Keep all the air intakes and the blower tube free of dust, lint, ha

A guard or other part that is damaged should be properly repaired or replaced by an authorised service facility, unless otherwise indicated in this Instruction Manual. Defective switches must be replaced by an authorised service facility. Do not use a tool if the switch does not turn the tool on and off correctly. 17. Use only approved parts. When servicing, use only identical replacement parts. Use an authorised service facility to fit replacement parts. Additional safety Instructions 1. This a

• Do not try to repair the tool or access internal parts. Contact authorised service centres only. 6 Unpacking Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Fitting the collection bag 1. Connect the strap (fig A) onto the hook on the underside of the bl

If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Preparation of the blower vac prior to use The ST1800 blower vac requires some assembly prior to use for the first time. This includes the fitting of the blow/vac tube to the housing, fitting the chute wheel assembly and the fitting of the collection bag. This section also covers the fitting and removal of the shoulder s