Proteccion para los ojos, los oidos y la cabeza Siempre al utilizar este equipo, pongase proteccion para los ojos con la marca de cumplimiento de la norma ANSI Z87.1, asi como proteccion para los oidos y la cabeza. Mantenga las manos y el resto del cuerpo lejos del area de la herramienta por donde sale disparado el sujetador. Mantenga lejos las manos Para reducir el riesgo de lesiones, el usuario debe leer y comprender el manual del operador antes de usar este producto. Lea el manual del operado

Repair or replace damaged parts. 21. NEVER LEAVE UNATTENDED TOOL CONNECTED TO AIR. Disconnect the air hose and do not leave tool until it is relieved of any built up pressure. 22. NEVER ALLOW UNTRAINED USERS TO USE THIS TOOL WHILE UNSUPERVISED. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP USING TOOL. Seek formal training or research books or magazines that specialize in pneumatic tools. 24. BE AWARE OF HOSE LOCATION WHEN USING PNEUMATIC TOOLS. Hoses can easily become a tripping hazard w

1. Damaged seal. 1. Replace damaged seals. Tool skips nails 1. Excessive air pressure. 1. Reduce air pressure to while discharging. 2. Air leaks. 3. Dirt in nose. 4. Dirt or damage prevents nails from moving freely. 5. Inadequate air flow to tool. 6. Worn piston O-ring or lack of lubrication. 7. Damaged trigger valve O- rings. 8. Worn bumper. 9. Cap seal leaking. tool. 2. Reseal and tighten screws and fittings. 3. Clean nose. 4. Clean magazine and inspect/repair damage. 5. Check fittings, hose,

Figure 3. Loading nails into magazine. 4. Slide the nails all the way down to the nose of the nailer. 5. Release the magazine pusher by pulling back on the pusher and pressing in on the catch lever. Operating If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer, do these steps: 1. Connect

Clean inspect the parts for cracks, wear, or burrs. 9. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with t

Before using your nailer, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer at a low setting, then increase the air pressure as needed for satisfactory results. An in-line filter/lubricator/regulator unit, can be installed as depicted in Figure 1. This filter/lubricator/regulator unit will protect your tool from damaging water build-up, allow you to adjust and maintain regulated air pressure to your tool, and save you the inco

Then tighten the clamping screws again _____________________________________________________________ Fig. 5: Horizontal alignment Fig. 6: Vertical alignment AOI 65 AON 65 AOP 65 Order Number 212340 212344 212348 Channels 21-69 21-69 21-69 Gain dB 7-9.5 8.5-13.5 9.5-15 Reception range MHz 470-862 470-862 470-862 Full width at half maximum Horiz. Vert. ° ° 58-40 90-65 57-32 70-44 50-28 59-31 Front-to-back-ratio dB 20-25 21-26 22-28 Mast clamp range O mm 22-60 22-60 22-60 Length mm 410 814 1345 Win

The wind load absorption of the tube (q = 1,100 N/m2), the reduced values apply. According to EN 50083-1, the mast clamping length must be at least 1/6 of the mast length. If the sum of the antenna wind load moments exceeds the values put in parentheses (. 1,650 Nm at clamping point), a structural analysis is required, according to EN 50083, part 1. KATHREIN-Werke KG .. Anton-Kathrein-Stra.e 1-3 .. P.O. Box 10 04 44 .. 83004 Rosenheim .. Germany .. Phone +49(0)8031 1840 .. Fax +49(0)8031 184306

must be in good order. Passers-by must not be endangered by falling objects. Secure the work/danger area. Mind that the technical values (e.g. wind load) of the antenna mast are not exceeded. Refer to the manufacturer if you do not know these values. Find an overview of the masts offered by Kathrein on the last page. Mount the antenna mast on solid ground only (walls, concrete, rafters) using the clamps, dowels and screws recommended by the manufacturer. Immediately leave the roof in case of a t

The air-o-steam combis are designed to form complete cook&chill systems together with the air-o-chill blast chillers/freezers, therefore, any installation can be tailored to meet the needs of the caterer. The air-o-steam combis detailed are 10 GN 2/1 electric Touchline models. OPERATING MODES • Selection window with three cooking modes (Automatic, Manual and Programs), cleaning cycles and setting mode. • Automatic mode: just select the family and food type and the oven will do the rest. Temperat