Wall24" Cabinet14" Minimum110. Wall24" Cabinet 34-1/2" Min. 24" Min. 23-3/4" 34-1/2" (36"with top canopy) 23-3/4"1-1/2" Locate Outlet 9" Max. 10-1/2" 26-1/2" Including Handle 23-3/4" Min. Note: Handle andhandle standoffdepth is 2-3/4" All models are factory set for a 110° door swing. For a minimum 90° door swing: • Allow 5-1/4" min. clearance to wall on the hinge side. For a full 110° door swing: • Allow 15" min. clearance to wall on the hinge side. Note: If installing between frameless cabinets

The filler strip will act as a spacer between the door case and adjacent cabinet and will prevent interference with cabinet door swing. The width of the opening must include filler panels. Note: When installed, the door should project forward 1” of adjacent 24”-deep cabinets. Location Requirements All Monogram Refrigeration Modules may be closed in on the top and sides as long as the front is unobstructed for air circulation and door swing. • Do not install these products where the temperatures

Whether you chose it for its purity of design or the assiduous attention to detail, you’ll find that your Monogram wine chiller’s superior blend of form and function will delight you for years to come. The information on the following pages will help you operate and maintain your wine chiller properly. If you have any other questions—please call the GE Answer Center® (800.626.2000). Contents Appliance Registration .................3 Built-In Dimensions .....................7 Care and Cleaning ..

The tinted glass will make the stained wood appear darker. A true color match can be seen only when the door is opened. • Apply the stain and sealer according to the manufacturer’s instructions. To avoid unpleasant odor, keep the door open to ventilate and allow the stain/sealer to dry completely before using the product. STEP 1 REMOVE PACKAGING • Remove corner blocks and foam drawer stops. • Remove all packing material, tape and protective plastic coverings. • Remove stainless steel toekick tap

IMPORTANT – Observe all governing codes and ordinances. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. WARNING – This appliance must be properly grounded. See “Electrical Supply”, page 4. AVERTISSEMENT – Cet appareil doit etre correctement mis a la terre. Consulter <>, page 4. If you received a damaged wine chiller, wine reserve or beverage center, you sh

Whether you chose it for its purity of design or the assiduous attention to detail, you will find that your Monogram wine chiller’s superior blend of form and function will delight you for years to come. The information on the following pages will help you operate and maintain your wine chiller properly. Contents Built-In Dimensions . . . . . . . . . . . . . . . .10 Care and Cleaning . . . . . . . . . . . . . . . .8, 9 Consumer Information . . . . . . . . . . . .2, 3 Controls and Features . . .

The cooler area will be in the middle section. The upper part of the cabinet is the warmest section. When the temperature is adjusted, allow 24 hours for the unit to stabilize. To set the control, turn it to the midpoint setting (approximately 45.F). Once the beverage center is loaded, allow at least 24 hours before making any adjustments to the initial setting. Interior light The interior light makes it easy to view your beverage labels and enhances the and switch display of your collection. Wh

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Preparing Secure all loose items such as drawers by Be sure the wine reserve stays in an upright taping them securely in place to prevent position during moving. to move damage. Built-In Dimensions Wine Reserve Installation dimensions The wine reserve can be a free-standing model or can be built in using the cut-out dimensions below. (603 mm) (603 mm) 233/4. 233/4. 341/2. (876 mm) P

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Reversing the Door Swing Wine Chiller To reverse the door Parts included: 1. Top left case hinge 2. Bottom left case hinge 3. Left and right side decorative hinge cover 4. Decorative hinge screw hole cover 5. Torx® driver bit Tools required: 1. Phillips screwdriver 2. Electric drill To remove the door: 1. Flatten the shipping carton to use as a pad. 2. Remove the 2 screws and the to

Pull the small slide sub-assembly completely forward. 3. Insert the sides of the drawer back into the guides. 4. Push until the tabs lock into place. Appearance may vary Sub-assembly Sub-assembly To replace, push drawer slide Pull small slide sub- arm back into unit assembly completely forward NOTE: Make sure the tabs on the full extension drawer guides are fully engaged before loading any bottles. Pull the drawers out all the way to the STOP position and push back in several times to make sure