Residual dirt and grass is easily removed immediately after mowing. 1. Remove grass deposits with a brush and a cloth. 2. Oil the red cutting mechanism lightly with thin oil (e.g. sprayed oil). 7. Troubleshooting DANGER! Cutting tool can cause injuries! V Wear suitable work gloves when rectifying faults. 10 Fault Possible Cause Rectification Abnormal Noises Screws / components loose v Tighten screws Foreign bodies on the blade. v Remove foreign bodies. Notch in the blade v Remove notches with gr
10. Turn cylinder 9 carefully. If the lower blade is set correctly 0 the paper will be cut off as if with scissors. 11. Repeat the cutting test on the other blades 9. 11 GB Regrinding/repairs: 8. Accessories A A On safety grounds, only original GARDENA spares may be used. Please contact GARDENA Service if it is necessary to replace the cutting tool, which will only become blunt after several years use if well-maintained. Repairs to the cylinder mower and the installation of the blades can be und
S Produktansvar Tillverkaren ar inte ansvarig for skada som orsakats av produkten om skadan beror pa att produkten har reparerats felaktigt eller om, vid reparation eller utbyte, andra an Original GARDENA reservdelar har anvants. Samma sak galler for kompletteringsdelar och tillbehor. I Responsabilita del prodotto Si rende espressamente noto che, conformemente alla legislazione sulla responsabilita del prodotto, non si risponde di danni causati da nostri articoli se originati da riparazioni eseg
1687079 For Prestige / 1800 / 2800 / GT / Conquest / 1700 / 2700 / YT Instructions 87151234567891081137141181610812788129128871281213 Kit Contents: 1687079, 54” Roller Bar 8 2860626 14 WASHERS Ref Part No. Qty. Description 9 1720159 2 ROLLERS, 2-3/4 x 2 1 1723008A 1 SHAFT & BAR ASSEMBLY 10 1678043 2 ROLLERS, 2-3/4 x 4-1/16 2 1704082 1 NUT, Hex Adjusting 11 1918459 2 COTTER, Pins 3 2860681 2 LOCKNUTS, Top Lock, 3/8-16 12 1678042 8 ROLLER W/BUSHINGS 4 1677507 1 SLIDE 13 1723009 1 BAR 5 1924361 1 W
1687077 For Conquest / 1700 / 2700 / YT / Broadmoor / 1600 / 2600 / LT Instructions 162345216111017687612197814969696969696918131513 Figure 1. Kit Contents: 1687077 Ref Part No. Qty. Description 11 1931352 1 CARRIAGE BOLT, 3/8-16 x 1-1/2 1 1716159A 1 ROLLER BAR, 44 Mower 12 1731383A 2 CAPSCREW, Hex, 5/16-18 x 1-1/2 2 2860681 2 LOCKNUT, Top Lock, 3/8-16 13 1919381 4 WASHER, 5/16 3 1677507 1 SLIDE 14 1731384 2 LOCKNUT, ESNA, 5/16-18 4 1924361 1 WASHER, 1/2 15 1731383 2 CHAIN, 2 Link 5 2172622 1 BO
Den Motormaher langsamer uber die Grasflache schieben. Batteriekapazitat fur hohe Reduzieren Sie die Belastung Schneidbelastungen zu gering. oder laden Sie Ihren Accu (siehe Kapitel 7.2 „ Der Accu“ ). Rasen wird gelb. Schnitthohe zu niedrig gewahlt. Schnitthohe korrigieren. Schnitt unsauber. Messer ist stumpf oder Messer vom GARDENA Service beschadigt. oder autorisierten Fachmann austauschen lassen. Konnen Sie eine Storung nicht beheben, wenden Sie sich bitte an eine der GARDENA Servicestellen (
1694561 For Baron / 2400 / RD Series Instructions 124356789101113131216151418171920151521212223 Kit Contents: 13 1708298 2 PIN, Round Head, Drilled, 3/8 x 1 Ref Part No. Qty. Description 14 1732511A 1 BRACKET, Mounting 1 1725959A 1 ROD & TUBE ASSEMBLY 15 1960074 4 CLIP, Hair Pin 2 1960033 1 CLIP, Hair Pin 16 1960585 2 CAPSCREW, Hex,5/16-18 x 1-3/4 3 1723124 1 BUTTON, Red 17 1725957 2 PAD, Rubber 4 1713995 1 GRIP, Soft, Black 18 1732510A 1 SUPPORT PLATE 5 1960674 1 PUSH NUT, 1/4 19 2157081 1 SPAC
PART NO. NO. DESCRIPTION REF. PART NO. NO. DESCRIPTION REF. PART NO. NO. DESCRIPTION 1 791762 Cylinder Assembly 26 791787 Ring Set 122 791717 Spacer.Carburetor 2 399269 Kit.Bushing/Seal (Standard) 125A 794588 Carburetor (Magneto Side) ....... Note ..... 127 694468 Plug.Welch 3 299819S Seal.Oil 791792 Ring Set 127A 691739 Plug.Welch (Magneto Side) (.020” Oversize) 130 691181 Valve.Throttle 5 791720 Head.Cylinder 27 690975 Lock.Piston Pin 133 398187 Float.Carburetor 7B .791716 Gasket.Cylinder Head
3. Drain the oil from the warm engine. Fill the engine crankcase with new oil. 4. Remove the spark plug from the cylinder. Pour one ounce of oil into the cylinder. Slowly pull the recoil-start grip so that the oil will protect the cylinder. Install a new spark plug in the cylinder. 5. Clean the dirt and debris from the cylinder cooling fins and the engine housing. 6. Clean the bottom of the mower housing. 7. Completely clean the mower to protect the paint. 8. Put the unit in a building that has
If the results of your work with the Lawn Scarifier become increasingly worse due to wear of the spring tines, the aerator cylinder can be adjusted twice. The aerator cylinder has 4 adjustment positions: • Transport position • Aerating position 1 : • Aerating position 2 : If the springs are worn (the scarifier roller is lowered by 3 mm). • Setting 3 : Second setting for worn springs (the scarifier roller is lowered by a further 3 mm). Push wear compensation lever D gently away from the housing a