4 OPERATION HAIR COTTER PINTRACTORHITCH PINOR MOWERCLEVIS PINREMOVE MOWER CLEVISPIN FROM THIS HOLE FIG. 5 OPERATION OPERATION GROUND LEVELCUTTING HEIGHTCUTTINGHEIGHTSHEIGHT ADJUSTMENT STRAPHEIGHT ADJUSTMENTLIFT LEVERLOCATING PINHAIR COTTER PINCLEVIS PINTOW BARADJUSTMENTTOW BARHAIR COTTER PIN1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" FIG. 6 OPERATION This mower has been designed to run offset from the center of the tow vehicle. This allows the operator to drive along side high brush with the tow veh

45-03621 45-03622 42" ROUGH CUT TRAILMOWER IMPORTANT: BATTERY REQUIRED!! The battery is NOT included with the deck but must be purchased separately. A 12 volt lawn tractor battery with 260/300 cold cranking amps and dimensions of 6-1/8"H x 7-5/8"L x 5-1/8"W is recommended to operate the machine. CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts FORM NO. 49463 (REV. 10/01/08) PRINTED IN USA 2 T

HA115321 SCREW 5/16-18 X 5/16 SOC. SET 50. 43555 WASHER 7/16" LOCK 51. HA181668 BOLT 7/16-20 X 1-1/4 HEX HEAD 52. 25051 COVER, GAS TANK 53. 25265 COVER, FRONT DRIVE 55. 43182 BOLT 5/16-18 X 3/4 HEX HEAD 56. 43064 NUT 5/16-18 HEX LOCK 57. 25264 COVER, REAR DRIVE 58. HA23732 TANK GASOLINE 59. HA24317 PLATE FUEL TANK 60. HA163318 SCREW 1/4-14 X 7/8 TAPPING PAN HEAD 61. HA23733 CAP GASOLINE TANK 62. 48837 HOSE FUEL TANK LONG 63. HA24455 HOSE FUEL TANK SHORT 64. HA23792 CLAMP FUEL LINE 65. HA23791 FI

NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the inner nut on the Clutch Cable. • Tighten the outer nut on the Clutch Cable. TO DECREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the outer nut on the Clutch Cable. • Tighten the inner nut on the Clutch Cable. • Repeat the above proce

FORM NO. 49464 (5/04) CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts Agri-Fab. TABLE OF CONTENTS SAFETY RULES ...................................................... 3,4 SAFETY AND OPERATIONAL DECALS ................ 5,6 HARDWARE CHART .................................................. 7 ASSEMBLY ............................................................ 8-11 OPERATION.....................

PULLEY CLUTCH LEVER PLUNGER REAR DRIVE.. COVER FOUR.. SCREWS CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clu

• Safety • Assembly • Operation • Maintenance • Parts PRINTED IN U.S.A. FORM NO. 49526 (2/05) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. IMPORTANT - READ THIS FIRST!!! For Missing Parts or Assembly Questions Please Call 866-576-8388 Mon.-Fri. 7 am - 5 pm CST. FAX 217-728-2032 or e-mail info@agri-fab.com Missing parts will be sent UPS in 24 hours directly to your home. TABLE OF CONTENTS SAFETY RULES..........................................................2 FULL SIZE HARDWARE CHART.

Este consciente del cambio de condiciones en las superficies inclinadas. Consulte las reglas de seguridad en el manual de propietario del vehiculo acerca de la operacion segura sobre superficies inclinadas. MANTENGASE FUERA DE LAS SUPERFICIES MUY INCLINADAS. 9. Siempre muevase hacia arriba o hacia abajo de una pendiente y nunca cruzando la pendiente. 10. Este equipo se debe operar a baja velocidad sobre terrenos escabrosos, a lo largo de arroyos y zanjas y sobre superficies inclinadas, para evit

Ajuste las tuercas. Vea la figura 9. 18. Ensamble la empunadura sobre el extremo de la manija elevadora. Vea la figura 9. OPERACION / AJUSTE Una extraccion regular de la paja es critica para el mantenimiento de una cesped saludable. La paja es una capa de tallos, recortes, plantas rastreras, raices y hojas que no se han secado todavia. Una acumulacion excesiva de paja impide que el aire, agua y fertilizante lleguen a las raices. El extractor de paja efectivamente extrae la paja excesiva de su ce

El extractor de paja de 40" se muestra en las ilustraciones. El procedimiento de ensamble es igual para el extractor de paja de 48". 1. Ensamble la placa elevadora al tope del protector de la horquilla usando cuatro pernos hexagonales de 5/16" x 3/4" y contratuerca hexagonal de 5/16" segun se muestra en la figura 1. Ajuste. 2. Invierta el protector de la horquilla. Vea la figura 2. 3. Ensamble dos (altos) soportes de montaje del brazo del enganche y dos soportes (cortos) angulares a los orificio