The Power-On Indicator, on the front of the heater, will illuminate when the heater is turned on. Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. Assembling Your Heater Remove all items from the packaging - the carbon tower body, front and rear bases. Unscrew the two screws from the base of the to

Since a fire risk may exist if the heater is covered or positioned incorrectly. 12. This heater is not intended for use in wet or moist locations. Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool. Do not immerse or allow liquids to be spilt on heater. 13. This heater has hot and arcing or sparking parts inside. Do not use in areas where petrol, paints, aerosols, or other inflammable substances are used or stored. 14. Do not operate the heater with the p

• Avoid placing items too close to the heater (both at the front and back) for optimal air flow Using Your Ceramic Heater Before First Use Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. Turning Your Heater On Plug the cord into a 230V or 240V power point and switch on. NOTE: To avoid an electrica

NOTE: After several seconds, the LCD screen will fade, but the heater settings will remain visible. Use the MODE button to select the desired heat setting. The mode button allows you to scroll through the various heating modes. HIGH – High heat setting (1800 watts) LOW – Low heat setting (1100 watts) AUTO – for use with the electronic thermostat FAN – for fan only operation To switch the heater into standby mode, press and hold the POWER/ SWING button until a beep sound is heard. Turn the heater

Convenient 8hr auto-off timer 7. 2 heat setting, plus auto mode and fan only setting 8. 90° degree oscillation for warmth throughout the room 9. On/Off button and variable temperature dial, to turn the heater on and off and to maintain your desired temperature setting 10. Power-On indicator Not Shown • Convenient carry handle • Safety tip-over cut-out switch KCE440_IB_FA.indd 6 12/10/09 2:26 PM Quick Start Guide The heater will start operating at the HIGH heat setting. Leave at HIGH until the ro

In Australia, this KAMBROOK Guarantee is additional to the conditions and guarantees which are mandatory as implied by the Trade Practices Act 1974 and State and Territory legislation. For service, spare parts or product information in Australia, please call KAMBROOK on the Customer Service Line 1300 139 798. For service, spare parts or product information in New Zealand, please call KAMBROOK New Zealand, Private Bag 94411, Greenmount, Auckland Phone 0800 273 845 Fax 0800 288 513. For spare part

Turn the heater on by switching the Power ON/OFF switch located on the back panel of the heater, to the ‘ON’ position. An audible beep will sound. The heater is now in standby mode. Using The Remote Control Your heater may be operated using either the control panel or the remote control. The remote control uses 2 x AAA batteries. To access the battery compartment, simply remove the cover at the rear of the remote control. To operate, ensure that you point KCE640_IB_FA.indd 8 16/10/09 10:50 AM Us

We ask that any electrical appliance that you use be operated in a sensible fashion with due care and attention placed on the following important operating instructions. Important Safeguards For Your Kambrook Convection Panel Heater • Carefully read all instructions before operating the Convection Panel Heater and save for future reference. • Remove any packaging material and promotional stickers before using the Convection Panel Heater for the first time. • Connect only to 230V or 240V power ou

3. This heater has three heat control settings OFF, ”LOW” HEAT AND “HIGH” HEAT, located at the top of the unit, along with an adjustable thermostat control. “LOW” HEAT (750W) is the lowest heat setting and “HIGH” HEAT (1500W) is the highest. 4. To select these settings DO NOT twist or rotate the heat control and thermostat control located on the top of the heater. To turn the heater on, grip the heat setting knob and lightly pull all the way up to the “HIGH” setting. There will be an audible cli

• Do not touch hot metal surfaces. • Do not allow power cord to contact hot metal surfaces. • Set the control setting to the OFF position then Unplug and allow heater to cool down before cleaning or storing. • The heater will not operate unless it is placed on a flat level surface as it is fitted with a tilt switch. • Do not use the heater with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorr