Pointing vent down protects regulator from weather damage. Figure 3 - Regulator With Vent Pointing Down Continued Hose Regulator Vent (pointing down) POL Fitting Supply Valve Propane Tank 3. Connect hose to inlet connector. Tighten firmly using a wrench. IMPORTANT:Extra hose or piping may be used if needed. Install extra hose or piping between hose/regulator assembly and propane tank. You must use the regulator supplied with heater. 4. Open propane supply valve on propane tank(s) slowly. Note:If

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC. CONTACT THE MANUFACTURER. ® FIRST EDITION PART NO. 18994 Printed In U.S.A. Price $1.00 SECTION PAGE CONTENTS Safety Information ......................................................................... 2 Product Identification .................................................................... 4 Unpacking...................................................................................... 4 Theory of Oper

2. Connect POL fitting on hose/regulator assembly to propane tank(s). Turn POL fitting counterclockwise into threads on tank. Tighten firmly using 7/8" wrench. IMPORTANT:Tighten regulator with vent pointing down. Pointing vent down protects regulator from weather damage. Supply Valve Propane Tank POL Fitting Hose Regulator Vent (pointing down) Figure 2 - Regulator With Vent Pointing Down 3. Connect hose to the inlet connector. Tighten firmly using 9/16" wrench. IMPORTANT:Use extra hose or piping

If a leak occurs, propane gas will sink to the lowest possible level. • Keep appliance area clear and free from combustible materials, gasoline, paint thinner, and other flammable vapors and liquids. Do not use heater in areas with high dust content. • Minimum heater clearances from combustibles: Outlet: 8 Ft. Sides: 2 Ft. Top: 6 Ft. Rear: 2 Ft. • Keep heater at least six feet from propane tank(s). Do not point heater at propane tank(s) within 20 feet. • Keep propane tank(s) below 100° F. • Chec

Keep this manual for future reference. Part No. 19226 Printed In U.S.A. Price $1.00 U.S. CONTENTS SAFETY INFORMATION SECTION PAGE Safety Information ......................................................................... 2 Product Identification .................................................................... 4 Unpacking...................................................................................... 4 Theory of Operation ...............................................................

Tighten 1/3 turn more using 5/8" socket wrench (4045 inch-pounds/4.5-5.1 n-m). 10. Attach nozzle assembly to burner strap. 11. Attach fuel and airline hoses to nozzle assembly. 12.Replace fan (see page 12). 13.Replace fan guard and upper shell. Nozzle (100/150 Models) 1. Remove upper shell (see page 12). 2. Remove fan (see page 12). 3. Remove fuel and air line hoses from burner head. 4. Remove spark plug cable from spark plug. 5. Remove spark plug from burner head using 13/16" open-en

They are needed to safely operate this heater. Follow all local ordinances and codes when using this heater. To Start Heater 1. Fill fuel tank with kerosene or No. 1 fuel oil. 2. Attach fuel cap. 3. Follow all ventilation and safety information. Continued 8 100577 4. Plug heater’s power cord into approved, grounded, three-wire extension cord. Extension cord must be at least six feet (1.8 meters) long. Extension Cord Size Requirement 6 to 10 feet (1.8 to 3 meters) long, use 18 AWG (0.75

18127-C Printed in U.S.A. PORTABLE SPACE HEATER OWNER’S MANUAL \\ \ \\ Models: HHC35A, HHC100A, and HHC150A IMPORTANT Read and understand this manual before assembling, starting, or servicing heater. Improper use of heater can cause serious injury. Keep this manual for future reference. NOTICE: For Servicing Dealer Information, see back page This heater is certified by the Canadian Gas Association to Canadian Standards Specifications B140.8-1967 and B140.0-1972. CONTENTS SECTION PA

12. Release hex-body of spark plug from vise. 13. Replace burner strap onto combustion chamber. 14. Attach spark plug wire to spark plug. 15. Attach fuel and air line hoses to nozzle assembly. 16. Replace fan (see Fan, page 8). 17. Replace fan guard and upper shell. Bend Here to Adjust Gap Gap Figure 18 - Spark Plug Gap, 35/55,000 BTU/Hr Models 45° Burner Strap Figure 19 - Spark Plug Rotation, 35/55,000 BTU/Hr Models Only Spark Plug (110/150,000 BTU/Hr Models) 1. Remove upper shell (see Upper Sh

Plug extension cord into standard 120 volt/60 hertz, three-hole, grounded outlet. Heater will start when extension cord is plugged into outlet. If not, push in flame-out control reset button (see Figures 5 and 6). To Stop Heater Unplug extension cord from outlet. To Restart Heater 1. Wait 2 minutes after stopping heater. 2. Repeat steps under To Start Heater. Flame-Out Control Reset Button Flame- Out Control Reset Button Figure 6 - Flame-Out Control Reset Button, 110/150,000 BTU/Hr Models Figure