Por ejemplo, no coloque la bateria en delantales, bolsillos, cajas de herramientas, cajas de juegos de productos, cajones, etc. con clavos, llaves, tornillos sueltos, etc. Transportar baterias puede provocar incendios si los terminales de la bateria entran en contacto accidentalmente con materiales conductores como llaves, monedas, herramientas de mano u objetos similares. Las Normas para Materiales Peligrosos del Departamento de Transporte de los EE.UU. (HMR) concretamente prohiben transportar

Debe dejar el paquete de baterias en el cargador y este ultimo comenzara automaticamente la carga cuando la temperatura de la celula suba o baje. 32 90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 33 2. El cargador y el paquete de baterias pueden estar calientes al tacto durante la carga. Esto es una condicion normal y no indica un problema. Para facilitar el enfriado del paquete de baterias despues de su uso, evite colocar el cargador o el paquete de baterias en un ambiente calido, como debajo de

Finally, use the special wing screw to secure the inside lower guard in position as shown in Figure 1. Test the lower guard for free operation by hand. The mitre clamp knob should now be threaded loosely into the pivot arm. Extension Cord When using the tool at a considerable distance from the power source, an extension cord of adequate size must be used for safety, and to prevent loss of power and overheating. Use the table below to determine minimum wire size required. Before using cords, i

Release the switch and allow blade to come to a complete stop. Then you can withdraw the saw, sight anew, and start a new cut slightly inside the wrong one. In any event, withdraw the saw if you must shift the cut. Forcing a correction inside the cut can stall the saw and lead to kickback. SUPPORT WORK NEAR CUT Figure 6 DON’T SUPPORT BOARD OR PANEL AWAY FROM THE CUT. Figure 7 IF SAW STALLS, RELEASE THE TRIGGER AND BACK THE SAW UNTIL IT IS LOOSE. BE SURE BLADE IS STRAIGHT IN THE CUT AND CLEA

Petersburg 33709, 5635 49th St., N...................................813-525-0273 Tampa 33609, 3432 W. Kennedy Blvd...................................813-872-8317 West Palm Beach 33415, 310 South Military Trail,...........407-689-3247 GEORGIA: Atlanta (South) 30349, 5330 Old National Hwy...............404-762-8844 Smyrna 30080, 2550 Cobb Pkwy,......................................404-956-0869 Stone Mountain (Atlanta) 30086, 5723 Memorial Dr........... 404-292-4714 HAWAII: Honolulu 96819,

Failure to do so can cause stalling and kickback. Any other conditions which could result in pinching, binding, twisting, or misalignment of the blade could cause kickback. Refer to the sections on “Adjustments and Set-Up” and “Operation” for procedures and techniques that will minimize the occurrence of kickback. TOOL LUBRICATION NOTE: With a new saw, change the oil after the first 10 hours of use and once per year after that. This action will greatly extend the life of your unit. 1. Always

Decker. SAFETY PRECAUTIONS WITH SAWS BRUSHES 1, Disconnect plug from power supply before changing blades, making cutting depth or cutting angle adjustments, lubricating, inspecting* or when saw is not being used. 2, When retracting thte lower blade guard, always use the retracting knob on the guard. 3, Never tie back the lower blade guard or its retracting knob, 4, When sawing never reach underneath the material for any reason, 5, Always be sure that the saw will be properly grounded befo

. 1003 11th Avenue, S.W. EDMONTON, ALBERTA ................ .11440 Ave.—142 Street HALIFAX, NOVA SCOTIA ....................803 McLean Street HAMILTON, ONTARIO...................180 Parksdale Ave., N. LONDON, ONTARIO____Kings Shopping Plaza (972 Hamilton Rd.) MONTREAL 10, P. Q...................7865 St. Lawrence Blvd. MONTREAL WEST, P. Q. .....................158 Ronald Drive OTTAWA, ONTARIO ................. ,418 Laurier Avenue, West DON MILLS (Toronto) ......................2 Valieybro

Dull blades may cause the saw to swerve or stall under pressure. IF YOU DROP or damage the saw, unplug it first; then check to see if the blade and lower blade guard operate freely before resuming operations. IF SAW STALLS, release the trigger and disconnect plug from power supply before attempting to loosen the unit. MOTOR Your Black and Decker tool is powered by a B&D-built motor. Be sure your power supply agrees with voltage marked on nameplate. Volts AC means Alternating Current (25 to 6

The use of any other accessory or attachement might be hazardous. The accessories listed in this manual are available at extra cost from your local dealer or Black & Decker Service Center, A complete listing of service centers is included on the owner’s registration card packed with your tool. If you need assistance in locating any accessory, please contact: Black & Decker (U.S.) Inc. Consumer Services Department 626 Hanover Pike P.O. Box 618 Hamstead MD 21074-0618 Every Black & Decker tool i