7.Hold the tool firmly with both hands. 8. When cutting metals, be cautious of hot flying chips. 9. Do not leave the tool running unattended. IO. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. Switch action To start the tool, simply pull the trigger. I Lock button Release the trigger to stop. For continuous 1 operation, pull the trigger and then push in 1 Trigger switch the lock button. To stop the

If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1 I.,;e only blades which are 1,140mm (44-7/8")long; 13 mm (1/2")wide; and 0.5mm (.020")thick. 2. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately. 3.Secure the workpiece firmly. When cutting a bundle of workpieces, be sure that all workpieces are secured together firmly before cutting.

Unsharpened or improperly set wheels produce narrow kerf causing excessive friction, wheel binding and KICKBACK. Wheel depth and bevel adjusting locking levers must be tight and secure before making cut. If wheel adjustment shifts while cutting, it will cause binding and KICKBACK. Use extra caution when making a “Pocket Cut” into existing walls or other blind areas. The protruding wheel may cut objects that can cause KICKBACK. 11. Use only diamond wheels. NEVER use tool with wood cutting blades

If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast ch

Failure to do so will shorten the service life of your blade and roller. CAUTION : 0 Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. 0 When not operating the tool, keep the lock-off lever in the SAFETY LOCK position. .Pulling the trigger hard when the lock-off lever is set to the SAFETY LOCK position can cause switch breakage. Operation Turn the tool on before contacting the workp

Pare siempre la operacion y cargue el cartucho de bateria cuando note menos potencia en la herramienta. 25 2. No cargue nunca un cartucho de bateria que este completamente cargado. La sobrecarga acortara la vida de servicio de la bateria. 3. Cargue el cartucho de bateria a temperatura ambiente de 10°C - 40°C (50°F - 104°F). Si un cartucho de bateria esta caliente, dejelo enfriar antes de cargarlo. 4. Cargue el cartucho de bateria de hidruro metalico de niquel cuando no lo utilice durante mas de

3. Rotate the blade installing lever in the (4) direction and remove the blade. 4. Rotate the blade installing lever in the (5) direction until it stops. (2)(3) (4) 002724 (5) 1 1. Blade installing lever 002723 5. With the blade installing lever held in this position, push it in the (6) direction. Then rotate the blade installing lever to its original position. (6) 1 1. Blade installing lever 002734 Anti-splintering device For splinter-free cuts, the anti-splintering device can be used. To insta

(2)Avoid storing battery cartridge ina container with other metal objects such as nails, coins, etc. (3)Do not expose battery cartridge to water or rain. 6. Do not store the tool and Battery Cartridge in locations where the tempera- ture may reach or exceed 5OoC (122OF). 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. SAVE THESE INSTRUCTIONS. Installing or removing the saw blade CAUTION: Always be s

Reducing vibration makes operator feel more comfortable when cutting various workpieces. Ergonomically designed rubberized grip provides more control and comfort. *balance plate mechanism: Counterbalance mechanism to reduce vibration by moving Plate in the opposite direction of Rod Electronic Control Variable Speed Control by Dial ensures optimum cutting speed per job. • Constant Speed Control keeps minimizing the speed loss under loaded conditions. • Soft Start suppresses the shock wh