GRACO INC. RO.Box 1441 MINNEAPOLIS, MN 55440-1441 @COPYRIGHT1991, GRAGO INC. HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safetymis pressure washer generates very high fluid pressure. Spray from the gun, leaks or ruptured components can inject fluid through your skin and into your body and cause extremely serious bodily injury including the need

If a pump protector/ winterizer is not available, *RV antifreeze needs to be run through the pump as outlined in the steps below. NOTE: Using a pump protector/ winterizer or *RV antifreeze is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. PRESSURE WASHER 1. Drain all water from high pressure hose, coil it, and store it in cradle of the pressure washer handle. 2. Drain all water from spray gun and wand by holding spray gun in a vertical p

Spray Gun: Connects with spray wand to control water flow rate, direction, and pressure. Quick Connect Spray Wand: Allows the user to quickly change out high- pressure nozzles. See How To Use Spray Wand instructions in this section. Chemical Hose (not shown): Feeds cleaning agents into the pump to mix with the water. See How To Apply Chemicals/Cleaning Solvents instructions in this section. BASIC ELEMENTS OF AN ENGINE Refer to the engine manual for location and operation of engine controls. Chok

NOTE: Using a pump protector/ winterizer or *RV antifreeze is to provide proper lubrication to the internal seals of the pump regardless of temperature or environment. PRESSURE WASHER 1. Drain all water from high pressure hose. 2. Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun holder. 3. Store chemical hose so it is protected from damage. 1. Obtain a funnel, six ounces of *RV antifreeze, and 16

7. Remove five colored quick connect nozzles from plastic bag and insert them into correct grommet on the nozzle holder. NOTE: Nozzles are color coded to match colored nozzles on panel. 8. Slide the formed rubber covers onto the handle's on-board hose and wand storage. 9. Add engine oil (supplied) to engine. Refer to Engine Owners Manual supplied by engine manufacturer for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. NOTE: The high pressure pu

49 - SP A17914 TERMINOLOGIA DE LA LAVADORA A PRESION PSI: (Pounds per Square Inch) Libras por pulgada cuadrada. Es la unidad de medida para la presion del agua. Tambien usada para la presion del aire, presion hidraulica, etc. GPM: (Gallons per Minute). Galones por minuto. Es la unidad de medida para el flujo promedio del agua a traves de la lavadora a presion. CU: (Cleaning Units). Unidades de limpieza. GMP multiplicadas por PSI. Modo de derivacion: Trabajando en modo de derivacion, la bomba est

2. Reduce the speed of the gasoline engine (RPM). Slow the engine down and the water pressure will go down with it. Step 3 is for models PCH2627, PCH3030 and PCH3540HR. 3. Adjust the pressure regulator on the pump. Turn the pressure regulator knob counterclockwise to lower pressure. Refer to the illustrations to identify your pressure regulator. Once you have finished using your pressure washer, return the pressure regulator to its original position by turning it clockwise. DO NOT attempt to inc

• Always wear ANSI approved Z87 safety glasses.Wear protective clothing to protect against accidental spraying. • Never point wand at, or spray people or animals. • Always secure trigger lock when wand is not in service to prevent accidental operation. • Never permanently secure trigger in pull back (open) position. 5- ENG D25803 D25803 6- ENG BOX CONTENTS Bagged Handle Bagged Parts Nozzle Cleaning Kit Engine Frame and Wheel Assembly High Pressure Hose Chemical Hose Engine Oil Spray Gun Knobs Sa

15- ENG D25804 TROUBLE SHOOTING GUIDE PROBLEM CAUSE CORRECTION Engine will not start (see Engine Manual for further engine troubleshooting) No fuel. Low oil (if equipped with low oil shutdown). Pressure builds up after two pulls on the recoil starter or after initial use. Not primed or choked. Spark plug wire not attached. Engine ON/OFF switch in OFF position (If applicable.) Choke lever in the “Choke” position on a “hot” engine or an engine that has been exposed to thermal heat for a long perio

See Operation section. Chemical Hose (not shown): Allows cleaners or cleaning solvents to be mixed with the pressurized water stream. See How To Siphon Chemicals/Cleaning Solvents in Operation section of this manual. 8- ENG D25805 BASIC ELEMENTS OF ENGINE Refer to the engine manual for location and operation of engine controls. Choke Control: Opens and closes carburetor choke valve Throttle Control Lever: Controls engine speed. Starter Grip: Pulling starter grip operates recoil starter to crank