For example, if a sample contains noise, you can lower the volume of the region containing the noise, to make it less obtrusive. * The tonal quality may change if you perform this operation repeatedly. * While you are adjusting the volume of a specified region in the sample, the Play BPM setting will be ignored, and the sample will play at its original BPM (tempo). 1. Press the pad of the sample whose volume you want to adjust for a specified region. 2. Press [WAVE EDIT]. 3. Press [F2] (AMP). Th

When switched off, the sound input to the INPUT jack is output without change. When set to “SLOW” When set to “FAST” Off Lit SLOW/FAST Pedal Switches the rotor’s rotation speed each time the pedal is pressed. 8 Operating the RT-20 Panel Operation For this description of using the pedals, first press the EFFECT ON/OFF pedal to switch on the effect (ON/OFF indicator lit), and press the SLOW/FAST pedal to switch the setting to SLOW (SLOW/FAST indicator off). In addition, set the knobs to the positi

Press the pedal to put the RC-2 into standby. The REC/PLAY/DUB indicator flashes rapidly Pressing the pedal once while the unit is in recording standby cancels recording. 4. Begin your performance. The RC-2 starts recording as soon as it receives audio input. 5. Press the pedal to stop recording. Playback of the recorded phrase begins simultaneously. 6. If you want to overdub onto the phrase, press the pedal. Each subsequent pedal press toggles between playback and overdubbing modes. * You can u

Using an AC adapter makes possible long performances with no worry about batteries going dead. GK IN Connector This connector is for connecting your guitar with a GK cable. NORMAL PU MIX Switch When Master is on, this switch determines whether or not the normal pickup sounds (or the sounds input to the GUITAR RETURN) are mixed. By mixing the normal pickup sound, you can create a sound that makes your guitar sound come alive. GUITAR OUT Jack Normal pickup signals input through the GK-2A are outpu

* The COMPRESSOR/LIMITER indicator goes off when this is set to OFF. NATURAL Provides natural-sounding performances with little thinning of the sound, even when pushing the effect. This is especially effective with slapping and hard picking. LIMITER Prevents distortion by suppressing the input signal level when it exceeds the set value. 160D SOFT Models the dbx 160 set to a lower compression ratio. 160D HARD Models the dbx 160 set to a high compression ratio. D-COMP Models the MXR DynaComp. THRE

The delay time can be set within the range of 200 ms to 1000 ms. PAN A panned delay in which the repeated sounds come alternately from the left and right channels. The delay time can be set within the range of 200 ms to 1000 ms. * When using the ME-50 in mono, the panning delay is not effective, even when PAN is selected. SPACE PAN This is a panning delay that gives an even wider spatial effect than PAN. The delay time can be set within the range of 200 ms to 1000 ms. * When using the ME-50 in m

OD/DS MOD DELAY 1 OVERDRIVE CHORUS 0-99ms DELAY 2 BLUES PHASER 100-700ms DELAY 3 DISTORTION FLANGER REVERB 4 METAL TREMOLO - 5 FUZZ ROTARY - 6 COMPRESSOR -- Blank Chart BANK NO. OD/DS MOD SOLO SW TYPE DRIVE TONE LEVEL SW TYPE RATE DEPTH LEVEL 1 1 2 3 1 2 2 3 1 3 2 3 1 4 2 3 1 5 2 3 1 6 2 3 1 7 2 3 1 8 2 3 1 9 2 3 1 10 2 3 Blank Chart Blank Chart EQ WAH NS MASTER LEVELSW TYPE TIME FEEDBACK LEVEL LOW LOWMID HIGHMID HIGH SW THRESHOLD Type List NO. OD/DS MOD DELAY 1 OVERDRIVE CHORUS 0-99ms DELAY 2 B

* El conector INPUT funciona tambien como interruptor de alimentacion. La unidad recibe alimentacion electrica cuando se enchufa el cable en el conector INPUT y no la recibe cuando no esta enchufado. Para evitar un consumo innecesario de la pila, asegurese de desconectar el cable del conector INPUT cuando no vaya a usar la unidad de efectos. 5. Conector EXP Conecte aqui un pedal de expresion (Roland EV-5, BOSS FV-500L/FV-500H; no incluido). Al pisar el pedal cambia la cantidad de cambio del tono

Press PARAMETER [ ] a number of times until the User Phrase settings screen is displayed. 5. Press PARAMETER [ ] [ ] to move the cursor, then rotate the PATCH/VALUE dial to set the User phrase. Step Pitch Length Sound Attack * When you want to place the currently set step at the very end, turn the PATCH/VALUE dial clockwise in the settings screen for the step that follows it (it does not matter which parameter is selected), until “---” appears in the bottom row of the screen. STEP Sets the step