What to do if you smell gas ..• Do not try to light any appliance. ..• Do not touch any electrical switch; do not use any phone in your building. ..• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. ..• If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. Please read this manual before installing or using this appliance. Retain th
18” (457 mm) à l’avant. Must exceed by 8" (203 mm) on the sides and at the back. 18’ (457 mm) at the front. Options 1 Ventilateur tangentiel à vitesses variables pour déflecteur de chaleur intégré Blower with variable speed for integrated heat exchanger #AC02050 PAR / BY : 1700, Léon-Harmel Québec (Québec) G1N 4R9 Tél.: (418) 527-3060 Fax: (418) 527-4311 info@drolet.ca
Un seul contrôle d’entrée d’air facile d’utilisation Easy-to-use single air-intake control Système autonettoyant de la surface vitrée en pyrocéramique permettant une excellente vision de la flamme Air-washed pyroceramic glass allows excellent flame viewing Coupe-feu en acier inoxydable Stainless steel baffle Déflecteur de chaleur intégré avec sortie d’air chaud à l’arrière Built-in heat deflector with rear hot-air vent Chambre de combustion recouverte de briques réfractaires assurant une m
• THIS STOVE IS NOT DESIGNED TO BE USED WITH THE DOOR OPEN. THE DOOR MAY BE OPEN ONLY DURING LIGHTING PROCEDURES. NEVER LEAVE THE STOVE UNATTENDED WHEN THE DOOR IS OPEN. • HOT WHILE IN OPERATION, KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS. WEAR GLOVES TO OPERATE YOUR STOVE. CAUTION • THIS APPLIANCE SHOULD BE MAINTAINED AND OPERATED AT ALL TIMES IN ACCORDANCE WITH THESE INSTRUCTIONS. • THE USE OF SOME TYPES OF PRESERVATIVE-TREATED WOOD AS A FUEL CAN BE HAZARDOUS. • D
9. You are now ready to connect your chimney to your stove. Simply install the inter-connecting stove pipe between the stove pipe adapter and the stove. You can follow the instructions in the following section (section 2.3) of this manual called « CHIMNEY CONNECTOR». 2.2.2 Typical installation through an existing masonry chimney You can also install your stove using your existing masonry chimney. To do so, follow the guidelines below. You may want to use a factory-built thimble, on construct you
• Roof guys (if required) Stove pipe • An adequate number of stove pipe sections. • A 90o elbow Typical installation through the wall FIGURE 2.2.1 (A) Typical installation through the wall 1-Start by positioning your stove where you would like it to go, taking into account the minimum clearances to combustible material. You will then be able to determine where the chimney will pass through the wall. You will probably have to adjust the stove position slightly to ensure that your chimney will run
35 3.1 SAFETY INFORMATION .............................................................................................................................. 36 3.2 FUEL ................................................................................................................................................................. 37 3.2.1 The use of manufactured logs ................................................................................................................... 38 3.2.2 Simple woo
Flue gases should reach at least 350oF before you close the stove’s primary air intake completely. Operate your unit within the comfort zone indicated on the thermometer; • To reduce the risk of smoke spillage into the room upon reloading your stove, leave the primary air intake completely open for a few minutes. This will heat up the chimney and build up draft before you open the stove door; • Maximize hot air circulation! Our wood stoves are designed to easily receive a variable speed blower t
Remove from the stove all bricks and insulation. 2. Install all side bricks (11 x 4 1/2" x 9" & 1 x 4 .” x 8 3/16") as shown in drawing below. 3. Install the back bricks (6 x 4 1/2" x 9") 4. Install the bottom bricks (4 x 4 1/2" x 9") + (2 x 6 " x 8") and the ash cap. 5. Install the "T" shape support. 6. Install the baffle bricks (4 x 4 1/2" x 9") + (2 x 3" x 9") on T shape support. 7. Finally, gently slide the insulation panels over the baffle bricks. Nbr. Description Qty 1 1 .” x 4 .” x 9” 25