Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 24   Tamaño del archivo: 64 kb   Fabricar: GE  
Categoría: Placa
@name

Replace side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes. STEP 3 INSTALL GRILLE PANEL ■ Remove the protective film from the appearance panel. ■ Raise the grille panel to the stop position. ■ Loosen the screws on the side trim behind the frame. Remove the bottom trim. ■ Slide the panel over the metal backer panel and into the trim. ■ If installing Stainless steel panels, first slide the filler panel into the tr

Descargado: 2   Tamaño del archivo: 64 kb   Fabricar: GE  
Categoría: Placa
@name

Replace side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes. STEP 3 INSTALL GRILLE PANEL ■ Remove the protective film from the appearance panel. ■ Raise the grille panel to the stop position. ■ Loosen the screws on the side trim behind the frame. Remove the bottom trim. ■ Slide the panel over the metal backer panel and into the trim. ■ If installing Stainless steel panels, first slide the filler panel into the tr

Descargado: 8   Tamaño del archivo: 135 kb   Fabricar: GE  
Categoría: Placa
@name

All Professional Ranges are factory set for natural or liquid propane gas. The correct model should be ordered for the installation situation. 36" Natural Gas Model ZDP36N4RHSS–4 gas burners and grill 36" Liquid Propane Gas Model ZDP36L4RHSS–4 gas burners and grill Note: Conversion kits (WB49X10132, Natural to LP and WB49X10133, LP to Natural) are available if the wrong gas type was ordered. High Altitude kit, WB49X10130 (for Natural and LP gas models), is also available. The kits must be instal

Descargado: 4   Tamaño del archivo: 135 kb   Fabricar: GE  
Categoría: Placa
@name

Optional Backsplash Accessories The range requires a 12" minimum clearance to a vertical combustible surface at the rear. A backsplash is required for installations with less than 12" clearance. The following backsplash accessories are available, or a custom, non-combustible backsplash can be used. Backsplashes: Order one with a 36"-wide range ZX12B36HSS–12" backsplash ZX22B36HSS– 22" backsplash with warming shelf Backsplash with Warming Shelf All Monogram Professional Wall-Mounted Hoods feature

Descargado: 1   Tamaño del archivo: 266 kb   Fabricar: GE  
Categoría: Placa
@name

Use a punch to create a pilot hole or drill a pilot hole. However, when drilling pilot holes be extremely careful. Do not drill holes a!l the wag through the countertop. Panel Support Note: Measurements are to Center of Holes Installation Instructions STEP 4 FASTEN PANEL SUPPORT BRACKET TO UNDERSIDE OF COUNTERTOP AND TOEKICK PANEL TO FLOOR Fasten the panel support bracket to the underside of the countertop using two #8 x 3/4" wood screws and two 3/16" flat washers. Mount Panel -Support Bracket I

Descargado: 6   Tamaño del archivo: 266 kb   Fabricar: GE  
Categoría: Placa
@name

The Side Panel Kit is not designed and handling parts for your protection. Proper installation is to support the countertop or cabinets, so it is important that the responsibility of the installer. they be fully supported prior to installing the kit. The kit may be used for either a left-hand or a right-hand opening. BEFORE YOU BEGIN -Readtheseinstructions completely and carefully. I M PO RTANT-Save these instructions for local inspector's use. IH PO RTANT-OBSERVECODES ALLGOVERNING AND ORDINANCE





Categoría