Lire tous les avertissements ci-dessous. AVERTISSEMENT 1. Les modeles ayant les numeros suivants peuvent etre utilises soit a l’interieur ou a l’exterieur en Canada. Les modeles ayant les numeros suivants doivent etre utilises a l’exterieur seulement en United States. ES-100, ES-200, ES-300, MS-100, MS-200, MS-300, ES-S100, ES-S200, ES-S300. Attention: La bouteille portative ne peut pas etre utilisee a l’interieur. Les modeles ayant les numeros suivants doivent etre utilises a l’exterieur seulem

There are no other warranties, expressed or implied, pertaining to this product or any other product sold by us. Empire Comfort Systems, Inc. neither assumes any responsibility in its behalf for operation of this or any other product manufactured or sold. shutter, lock in place by tightening the air shutter screw.Page 2 CAUTION: MAXIMUM WORKING PRESSURE 1/2 P.S.I. 11-INCH WATER COLUMN R-3088 (LOW PRESSURE REGULATOR IS REQUIRED) RECHAUD A GAZ DE SUPERB R-3088-F Instructions d’Assemblage Date d’En

An unnecessary high flame is wasteful and inefficient. 3. The air shutter for each burner should be adjusted so the flame burns clean without blowing. After you obtain the correct setting or the air ADJUSTING PIN ADJUSTING HOOD ADJUSTING HOOD DUST COVER STEM VALVE BODY CAUTION: Orifice HOODS must again be turned down, if the gas stove is to be used on LP gas after it has once been adjusted for other gases. GAS ENTRANCE HOLE IN. ADJUSTING PIN SHOULDER UNDER NO CIRCUMSTANCES SHOULD ANY ALTERATIONS

Place propane tank from cooker so that the hose length will not be in the way. Keep all connections and fittings clean, replace any damaged parts. 19. Never store the propane tank near high heat, open flames, direct sunlight or where high temperature exist. Assembly Instructions REQUIRED TOOLS: Pliers or adjustable wrench and screwdriver. 1. Bolt legs in place by inserting short bolts through holes in corners of main top, then through slot at top of leg. Screw nuts onto the bolts. Attach drip pa

Carefully follow lighting instructions. 11. Keep children and pets at a safe distance. 12. Never place empty containers over an open flame. 13. Do not attempt to change valve depth into burner or reassemble parts. 14. Never store propane tank in an enclosed area. If cooker is stored in doors after use, disconnect the propane tank for outdoor storage. 15. The Superb regulator and hose assembly must be used, no substitutions. Other regulators or no regulator used at all could result in dangerous g

3. Re-open brass control valve 1/4 turn. 4. Keeping hands and face away from the top of the burner, light with a fireplace match or long-nose lighter. 5. Adjust the brass control valve for desired flame height. R-3088 Empire Comfort Systems, Inc. . 918 Freeburg Avenue . Belleville, IL 62220 Page 1 SECTIONAL PARTS FOR GAS STOVE SP-010 SP-011 SP-012 SP-064 SP-063 SP-065 SP-066 SP-067 SP-013 SP-014 SP-015 P-220 P-219 SW2-1 SW3-1 R-3445 SP-034 SP-062 P-221 R-3337 SP-028 SP-055 SP-016 S-1377 R-3339S-

WARNING 1. The following model numbers are for indoor or outdoor use in Canada. The following model numbers are for outdoor use only in United States. ES-100, ES-200, ES-300, MS-100, MS-200, MS-300, ES-S100, ES-S200, ES-S300. Attention: Portable (20 lb.) cylinder can not be used indoors. The following model numbers are for outdoor use only in Canada and United States. SE-200 and SE-300. 2. Do not leave appliance unattended while in use or hot. Never move cooker while in use or hot. 3. A fire can

(This shuts off flow of gas from the regulator to the burner. 2. Open LP cylinder valve or gas supply by 1/4 turn. This allows gas into the regulator and stops it at the brass control valve. 3. Apply gas detector fluid (or soapy dishwashing solution) on all connections, especially around the regulator, valve and POL-cylinder GRATE BURNER TOP 1/4" BOLT 1/4" HEX FLANGE NUT BODY LEG Model No. SE-200 w/SLK-28 VALVE KNOB connection. Any bub-bles that appear indicate a gas leak. If so, turn off gas an

Apply nuts and tighten securely. Now tighten leg bolts. 2. Install manifold clamps. Insert two long bolts through manifold clamp holes in the main top. Attach the two manifold clamps loosely (10,000 Btu per Burner) underneath top, using nuts. Place manifold pipe with valves attached into the clamps. Align the gas valves with center of large opening in top. The adjusting hood of the valve should face the rear of the stove. Now tighten the manifold clamps securely. Place the valve knobs on valve s

If LP gas is to be used, no adjustments should be necessary. Orifice HOOD can be open slightly to get desired flame. 2. For use with Natural or Manufactured gas open HOOD until the proper amount of gas is fed to each burner. When properly adjusted the flame should have greenish blue inner cones about one-half inch long. An unnecessary high flame is wasteful and inefficient. 3. The air shutter for each burner should be adjusted so the flame burns clean without blowing. After you obtain the correc