One Cornelius Place Anoka. MN 55303-6234 Telephone (800) 238-3600 Facsimile (612) 422-3246 INSTALLATION INSTRUCTIONS KIT, P/N 2267 & 2329 Remcor model DB100/150 dispenser with: 1. Manitowoc Series B320, 420 Ice Maker - Refer to Fig 1. 2. Ice-O-Matic Series GC300 Ice Maker - Refer to Fig 2. 1. Seal cover to dispenser as follows: A. Apply a bead of RTV on the hopper flange. B. Set cover onto the dispenser. Be careful not to disrupt the dispenser cabinet labels, if present. C. Wipe away e

Applicable Ice Maker Models ICEMAKER MODELS SIZE (WIDTH) Cornelius 322/522 (includes AC/WC 322) 22” Crystal Tips 200/300/400 22” Ice-O-Matic GC 300/550 22” Manitowoc 320/420 22” Scotsman SLC 300/400 22” Servend S2/4 22” Table 2. Loose Shipped Parts Item No. Part No. Name Qty. 1 52994 Cover, Gray - 08008 1 52934 Cover, Black - 02390 1 2 15506 Lid Assembly 1 3 29565 Bracket 2 4 70217 #8 Screw 6 5 50904 RTV 1 6 90221 Label 1 7 92111 Installation Instruction 1 8 620701902 Acorn Nu

1-800-238-3600 ILLUSTRATE PARTS LIST Self-Contained Flaked Ice Maker Model: Series 200, 525, 725 (R404A Refrigerant) FIGURE 1. Exploded View Self-Contained Flaked Ice Maker Illustrated Parts List 1 of 3 © IMI Cornelius Inc., 2004 Revision: A Part Number: 166240010IPL May 6, 2004 Parts List Item No. Description 200 525 725 1 Compressor (115V 60HZ) 162964053 162964011 162964011 Compressor (220V 50HZ) 162964054 162964038 2 Pad, Masonite 09115 36310 36310 3 Hold-Down, Evaporator 16327

Cabinet Exploded View Cabinet Parts List Item No. Description AF200PSCR AF200PSC50R AF200SSCR AF525PSCR AF525PSC50R AF525SSCR AF725PSCR 1 Bin Door 09120 09120 09120 09120 36555 2 Door, Track, LH 25007 25007 25007 25007 25007 3 Door, Track, RH 08824 08824 08824 08824 08824 4 Door Trim 09112 09112 09112 09112 08681 5 Back Panel 163278001 25043 N/A N/A N/A 6 Front Panel 163275002 25853 163283002 26857 163283001 7 Side Louvered Panel 163275013 163275014 N/A N/A N/A 8 Upper Louvered Access

NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 seconds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper front panel. 1. Remove the top plastic bin covers (2) from the dispenser. 2. Place the ice maker adapter lid assembly (item 1) on top of the dispenser and position it flush with the rear and sides of the dispenser as shown in Figure 1. 3. Install the ice baffle on the lid assembly as shown in Figure 2. Rel

NOTE: Adjust the automatic agitation timer located in the dispenser’s electrical control box to 5 seconds on, 20 minutes off. Access to the timer is provided by removing the merchandiser/upper front panel. 1. Remove the top plastic bin covers (2) from the dispenser. 2. Place the ice maker adapter lid assembly (item 1) on top of the dispenser and position it flush with the rear and sides of the dispenser as shown in Figure 1. 3. Install the ice baffle on the lid assembly as shown in Figure 2. Rel

Secure the brackets using the #10 sheet metal screws provided. 7. Follow the ice maker manufacturer’s instructions to complete the installation of the ice maker including the bin thermostat if so equipped or required. IMPORTANT: For Scotsman CM series ice makers with sonic ice level control, Bin Thermostat Kit KSB1 must be ordered with the ice maker ! CAUTION: The bin thermostat location must not interfere with agitator rotation. 8. Locate the cleaning caution label (item 5) on the manual ice fi

30.30” (BACK SIDE OF DISPENSER) 1.67” 27.40” ICE MAKER DROP ZONE 21.50” AND BIN STAT MUST FIT WITHIN THE 27.40 X 21.50” OPENING Figure 1 ! WARNING: Disconnect power to the unit before installing adaptor following all lock out / tag out procedures established by the user. Verify all of the power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to the equipment. ! WARNING: All of the attachment screws and plates must be installed as d

Place shaft seal locator seat over gear motor output shaft, embossed side down, and push down until shaft seal seat rests flush on top of gear motor. 2. Place rubber coated ceramic seal E–RING (important: ceramic face up) over output WASHER, PLAIN FLAT shaft and push down until seal rests on top of the shaft seal seat. (Lubricate rubber on SHAFT SEAL ceramic seal with rubber lubricant.) LOCATOR SEAL 3. Place shaft seal with carbon face down (spring up) over output shaft and push (gently) downwar

NOTE: Cold water will absorb heat faster than warm water. The water flow will therefore automatically increase as inlet temperature increases. SIGHT GLASS THERMOSTATIC EXPANSION VALVE FIGURE 12. EXPANSION VALVE FIGURE 13. ADJUSTMENT SCREW © 2004-2005, IMI Cornelius Inc. - 13 -Publication Number: 630460174SER Continuous Flow Icemaker Service Manual CONDENSER MODULATING VALVE REMOVAL 1. Disconnect power to unit, then shut off water supply to condenser and evacuate refrigerant from system. 2. Remov