b. Water line connection is loose or not seated properly. c. Defective water valve. d. Stripped threads. a. Replace water valve. b. Insure that threads are not cross- threaded and tighten. c. Replace water valve. d. Replace water valve. 8. Water leaking from rear of toilet bowl. a. Worn or defective vacuum breaker. b. Loose vacuum breaker. c. Cracked or defective toilet bowl. a. Remove white cap from vacuum breaker. Flush toilet. If water leaks during flush, vacuum breaker needs to be replaced.

Service Offic. The Dometic Corp. 509 South Poplar St. LaGrange, IN 4676. CANAD. Dometic Dist. 866 Langs Dr. Cambridge, Ontari. CANADA N3H 2N. Catalina 2500 INSTALLATION & OPERATING INSTRUCTIONS REVISIO. Form No. 3103624.023 3/98 (Replaces 3103624.015) (French 3108310.024) ©1998 The Dometic Corporatio. LaGrange, IN 4676. A&E CATALINA 250. A&E CATALINA 250. INSTALLATION/OPERATIO. APPLICATIO. The A&E Catalina 2500 Case Awning is designed an. intended for direct mounting on straight and most curve.

Do not attempt installation without first contacting a VacuFlush Certified Dealer, your nearest VacuFlush Parts Distributor, or Dometic. WARNING ! WARNING Dometic Corporation • Sanitation Systems 13128 State Rt 226, PO Box 38 Big Prairie, OH 44611 SeaLand Product Customer Service: 1-800-321-9886 (8:00 a.m. - 5:00 p.m. ET) This manual must be read and understood before adjustment, maintenance, or service is performed. Modification of this product can result in property damage. 2 TABLE OF CONTENTS

2. Water will not stay in bowl. a. b. Dirt or debris on underside of flush ball seal. Worn or damaged flush balland seal. a. b. Put Mode Switch in "Service" position and clean underside offlush ball seal. Remove toilet from floor, disassemble bowl from base, and replace flush ball and seal. 3. Water leaks onto floor. a. b. c. d. Toilet loose. Defective component under chinabowl: vacuum breaker assembly, water hose/fittings, water valveassembly, upper bowl seal, baseO-ring, rotor shaft, or plasti

We recommend using a long-neck screwdriver or 7/16-in. socket for the operation shown below. NEVER PRY OPEN THE FLUSH BALL FROM INSIDE THE TOILET BOWL. Damage to the flush ball and bowl seals may result. 1. Remove PC board access cover. Place Mode Switch in the “Manual Override” position. This disconnects flush valve motor brake from electrical circuit. 3. Insert screwdriver or 7/16-in. socket through access hole and onto hex head. Manual Override position 4. Turn screwdriver or socket wrench co

(Pam® cooking spray, Pine-Sol® cleaner, Wd-40®® Sani-Flush is a registered trademark of Reckitt Benckiser Inc. lubricant, etc.). ® Teflon is a registered trademark of DuPont Co. ® WD-40 is a registered trademark of WD-40 Company. fig. b fig. A WINTeRIzING At the end of each traveling season, the SeaLand toilet should be winterized for storage by using potable water- safe antifreeze in the system. To use antifreeze: . Empty the blackwater tank. 2. Thoroughly flush system with fresh water. 3. Empt

Dometic Corporation 13128 State Rt. 226, P.O. Box 38 Big Prairie, OH 44611-0038 USA 330-496-3211 1-800-321-9886 • Fax: 330-496-3097 ® Registered; ™ Trademark of Dometic Corporation © Dometic Corporation TABLE OF CONTENTS Toilet Model Identification ......................................2 Toilet Dimensions ..................................................3 Installation Instructions.....................................3 - 6 Toilet Operation ..................................................... 6

Modification of this product can result in property damage. Dometic Corporation • Sanitation Systems 13128 State Rt 226, PO Box 38 Big Prairie, OH 44611 SeaLand Product Customer Service: 1-800-321-9886 (8:00 a.m. - 5:00 p.m. ET) 2 TABLE OF CONTENTS Toilet Model Identification . . . . . . . . . . . . . . . . 2 Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . 2 Concerto Toilet Dimensions . . . . . . . . . . . . . . . 3 Toilet Installation Instructions . . . . . . . . . . 3 - 6 Remote

Install the flange gasket over the T-bolts (fig. 10). STEP 12: Install floor flange adapter with words “THIS SIDE UP” facing up. Tighten adapter to floor flange using four flat washers and hex nuts. Tighten in criss-cross pattern (fig. 11). STEP 13: Temporarily set the toilet in place on the floor flange (fig. 14). STEP 14: Mark the holes for the two toilet mounting bolts (fig. 15). STEP 15: Pick up toilet and set aside. Drill 3/16-inch pilot holes in the floor (fig. 16). IMPORTANT: If replacing

Do not attempt installation without first contacting a SeaLand Product certified dealer orDometic Corporation. WARNING! This manual must be read and understood before adjustment, maintenance, or service is performed. Modification of this product can result in property damage. Dometic Corporation • Sanitation Systems 13128 State Rt. 226, P.O. Box 38 Big Prairie, OH 44611-0038 USA SeaLand Product Hotline 1-800-321-9886 (8:00 a.m. -5:00 p.m. ET) TABLE OF CONTENTS Page Product Features. . . . . . .