En California, los motores pequenos (no para el uso en automoviles) estan disenados, construidos y equipados para cumplir con las normas exigentes de anti-smog del Estado de California. En otros estados, los motores nuevos (no para el uso en automoviles) de 1997 para adelante deben cumplir las normas federales exigentes de la EPA de anti-smog. Shindaiwa Corporation debe garantizar el sistema de control de emision de su motor pequeno (no para el uso en automoviles) durante los periodos mencionado

A blade with worn teeth besides providing poor performance might also generate a sudden thrust. This can result in a violent sideways kick caused when the blade touches against wood or solid bodies, such thrust might then cause the operator to loose control of the machine itself. Never attempt to work with a damaged blade but replace it with a new one. THRUST: can occur when using any type of circular blade within the risk area: therefore it is advisable to cut using the remaining area of the bl

Usted es responsable de la presentacion del motor al distribuidor autorizado de Shindaiwa Corporation mas cercano cuando exista algun problema. Si el distribuidor Shindaiwa no puede responder su pregunta con respecto a sus derechos y responsabilidades de garantia, debera entonces comunicarse con su distribuidor regional de Shindaiwa. Para obtener el nombre y el numero telefonico del distribuidor de Shindaiwa en su localidad, comuniquese con Shindaiwa Inc., al (503) 692-3070 de 8:00 a.m. a 5:00 p

• Transport with clean reflectors, SMV and working lights as required by federal, state, and local laws. M100 WARNING 540 RPM SPEED RANGE ONLY HIGHER PTO SPEEDS CAN CAUSE PERSONAL INJURY AND EQUIPMENT FAILURE 101101 REMEMBER: If Safety Signs have been damaged, removed, become illegible or parts replaced without Signs, new Safety Signs must be applied. New Safety Signs are available from your authorized distributor or factory. 16 INSTRUCTIONS TRACTOR REQUIREMENTS AND PREPARATION The models SDM40-

SAE 30 OR 10W30 MOTOR OIL LUBRICATION ** REFER TO MAINTENANCE "ENGINE " Keep unit well lubricated (See "LUBRI SECTION. CATION CHART"). 11 _,CAUTION: Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Remove fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot muffler or cyl

(All 4 Models have 4 position skids) Driveline Shear Bolt Standard, Slip Clutch Optional Approximate Weight 366 lbs 418 lbs 470 lbs 532 lbs Warranty 1 year limited warranty FEATURES Available in major tractor colors SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Ref. 2 (A) 1 15 1107383 Washer-Flat, 3/8........................ ... 2 1901271 Handlebar, Upper - Incl. Ref. 2 (B) 1 16 1100044 Bolt-Hex Hd., 5/16-18x3/4...... ... 2 2 1916928 Decal-Forward Clutch Bail............ 1 17 55081 Support, Handlebar (A).............. ... 2 3 9854 Bolt-Curved Hd„ 5/16-18 x 1-1/2.. 6 1902173021 Support, Handlebar (B).............. ... 2 4 1100806 Bolt-Hex Hd„ 1/4-20x1-1/4......... 1 18 1110107 Locknut-Hex Hd., 5/16-18......... ... 2 5 55044 Bracket, Cable........

STEP 5 Raise the tiller and remove the blocks. Lower the tiller to the ground. STEP 6 With the tractor at idle RPM and the tiller lifted off of the ground, engage PTO and slowly advance throttle to 540 PTO RPM. NOTE: Rotary tiller is designed to run at 540 PTO RPM only. STEP 7 Select a low gear for the tractor and begin to move forward. Tractor ground speed is to be controlled by gear selection only and not engine speed. As the tractor moves forward, slowly lower the tiller down. Allow the tille

When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! ! © Copyright 2012 Printed APS1548, APS1560, APS1572 & APS1586 All Purpose Seeder 313-354M APS1548 30256 30255 Operator’s Manual APS1586 7/11/12 Table of Contents Important Safety Information . . . . . . . . . . . . . 1 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . .1 Look For The Safety Alert Symbol . . . . . . . . . . .

Use the list that is for your Overseeder as a checklist to inventory parts received. Please contact your local Land Pride dealer for any missing hardware. Tools Required: • Safety glasses • Work gloves • Pencil • Tape Measure • Center punch • Hammer • Electric drill with 21/32" drill bit • Extension cord (if required) • Set of wrenches • 3/8" or 1/2" ratchet wrench set Further Assistance Your dealer wants you to be satisfied with your new seeder. If for any reason you do not understand any part