Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 1   Tamaño del archivo: 220 kb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

All adjustments or repairs must be done with the sander disconnected from the power source, unplugged. Failure to comply may result in serious injury! The PDS-12CS disc sander is rated 115V/230V, Prewired 115V. If you want to run the PDS-12CS on 230V refer to the wiring diagram found on the inside of the switch box cover (I, Fig. 8). Before hooking up to the power source, make sure that the switch is in the off position. 11 Emptying the Collector Bag Optional Accessories .. CAUTION Wearing a par

Descargado: 1   Tamaño del archivo: 1 mb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

The oscillating movement of the belt is by design. Observe the belt's range of movement from its highest to lowest position. The edges of the belt should not have a tendency to move above or below the edges of the rollers. If adjustment is still necessary: 3. Insert the round shaft of the belt tracking tool (provided) into the micro adjust lock nut (A) and turn away from you to loosen. 4. Turn the micro adjusting screw (B) in 1/4 turn increments until the belt tracks evenly on the rollers when r

Descargado: 1   Tamaño del archivo: 518 kb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

6. Tension belt by pushing handle to the right. 7. Reinstall the belt guards Note: Belts stretch with wear. You may have to adjust tracking with a new belt. Belt Tracking Adjustment 1. Disconnect the machine from the power source. 2. Push the belt by hand in the direction indicated on the belt cover. Observe the belt position on the rollers. Edge of belt should remain even with the edge of the rollers. 11 3. Insert the driver with the round shaft, supplied with the machine into the micro adjusti

Descargado: 0   Tamaño del archivo: 3 mb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

If the breaker is tripped, turn the sander off and reset the circuit breaker by pressing the button (Figure 2, Item C). Be sure to turn the sander off before resetting the circuit breaker to avoid unintentionally starting the sander 9 This Page Intentionally Left Blank 10 Conveyor Belt Tracking Belt tracking adjustment may be necessary during the break-in period and normal operation to compensate for belt stretching. Abrasive belt tension must be properly adjusted before adjusting the tracking.

Descargado: 29   Tamaño del archivo: 1 mb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

16). JET offers a wide variety of hoses, adapters and dust collectors. 2. Loosen the wing nut (B, Fig. 16) and pull the gate (C, Fig. 16) open to allow air suction to the sanding belt. Push the gate closed to shut off air suction. Tighten the wing nut. 3. Push the gate (D, Fig. 16) down to shut off air suction to the disc. Lift the gate to open the air suction to the disc. Lubrication All moving parts run on sealed ball bearings and require no lubrication. Optional Accessories Open Stand w/Belt

Descargado: 7   Tamaño del archivo: 231 kb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

9 10 Troubleshooting Trouble Possible Cause Solution Sander will not start 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 4. Starting capacitor bad 1. Check all plug connections 2. Replace fuse or reset circuit breaker 3. Replace cord 4. Replace starting capacitor Sanding drum does not come up to speed 1. Extension cord too light or too long 2. Low current 1. Replace with adequate size and length cord 2. Contact a qualified electrician Machi

Descargado: 1   Tamaño del archivo: 207 kb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

Tighten the nuts to secure the sander to the stand. Note: If you are going to use the sander as a benchtop unit mount the sander to the workbench with the supplied bolts. 2. Unscrew the knob (A, Fig. 2), remove the washer (B, Fig. 2) and the trunnion holder (C, Fig. 2). Repeat for opposite side. 3. Lift the table (D, Fig. 2) into position and set on top of the split pins and threaded shaft. 4. Reinstall the trunnion holder, washer and knob. Repeat for opposite side. 5. Make sure the trunnio

Descargado: 1   Tamaño del archivo: 1 mb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

A. A temporary adapter (Fig. B) may be used to connect the plug to a two- prong receptacle (Fig. B) if a properly grounded outlet is not available. A temporary adapter should only be used until a properly grounded outlet can be installed by a qualified electrician. This adapter is not applicable in Canada. The green colored lug must be fastened to the cover plate screw. Important: The adapter illustrated in Fig. B is for use only if you already have a properly grounded two-prong receptacle. Do n

Descargado: 6   Tamaño del archivo: 2 mb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

The depth of cut is controlled by the height adjustment handwheel. It may take some experimentation to determine the proper depth of cut, given the variables of abrasive grit, type of wood, and feed rate. For best results, use scrap wood to practice sanding and to develop skill and familiarity with the machine before doing finish work. A combination of several variables will determine the proper depth of cut to use, including the following: 1. Abrasive type and grit size. 2. Width of the piece b

Descargado: 4   Tamaño del archivo: 155 kb   Fabricar: Jet Tools  
Categoría: Máquinas de rectificar
@name

91-603 The Gold Standard Since 1921. POMMMIVC





Categoría