. Introductio. Clocks & Timer. Features and Function. Cooking Guid. Roasting Guid. Cooktop. Cleanin. Installation Instruction. Warrant. Safety Instruction. First Us. Side Mounted Power Outlet. Accessorie. Ringer Timer Mode. Analogue Clock Mode. Automatic Cooking Using the Analogue Cloc. Main Oven Feature. Cooking Guid. Roasting Guid. Radiant Cooktop. Cleaning your Rang. Cleaning your Cookto. Installing Your Produc. Manufacturer's Warrant. Product Details & Customer Car. Customer Car. . . . . . .

INSTALLATION INSTRUCTIONS CONTENTS Contents of packaging Equipment required Optional accessories 1 x canopy hood Electric drill Light bulb 104467 2 x chimney pieces Drill bits Chimney ext. (10’ ) SS 8 x angle brackets Spirit level Chimney ext. (10’ ) IR 1 x installation instructions Screwdriver Charcoal filter 103821 4 x filters ( part number 104660) Jig saw Recirculation kit 1744 Installation kit ( part number 104922) Ladder 4 x 12 x 40mm screw Tape measure 30 x 6 x . ” self tapping screw Duct

• To comply to electrical safety regulations this canopy must be plugged into a socket near the appliance. The socket must be accessible and enable the end user to isolate the canopy from the power for the purpose of internal cleaning or maintenance. Ducting accessories are not supplied. All ducting must comply with local requirements and building codes. The canopy hood is heavy please ensure adequate care when installing the canopy hood to prevent personal injury. The canopy hood must be instal

This distance shall be at least 650mm if the rangehood is installed over a gas hob. • That regulations concerning the discharge of exhaust air have to be fulfilled. • If the supply cord of this equipment is damaged, it must only be replaced by the manufacturer or its service agent or similarly qualified person in order to avoid a hazard. Electrical Rating: 280W (1.16A) Max. at 240V 50Hz 87621 WHITE 600mm 87622 BLACK 600mm 87623 STAINLESS 600mm 87647 WHITE 900mm 87648 BLACK 900mm 87649

If t' rangehood is to be installed as ducted unit, remove the duct knock-out (top or ensure the vent cover is in place. Refer also to Ducting Options. OPERATION After your Rangehood is fixed in position: 1. Check that the light and the diffuser are in place. 2. See that the filters are correctly positioned. 3. Plug into 230/240V 3 pin outlet. Keep cord clear of stove elements or hot utensils. Permanent wiring to house supply, or modifications to plug or wire should be carried out by a regi

13. Connect to the power supply and switch on the power using switch/socket outside the canopy hood. 14. Slide the upper chimney piece up to the ceiling and secure in place with four screws supplied. INSTALLATION – RECIRCULATED For recirculation do not cut the 170mm hole into the ceiling and purchase the charcoal filters and recirculation kit 1744. The recirculation kit must be used to channel the air to the top of the flue. For other accessories parts and service please contact your local suppl

b) Use a small bladed screwdriver to prise off the light cover. c) Use a cloth to remove the bulb. Do not touch the bulb with fingers. d) Replace with a new bulb using a cloth. Do not touch the bulb with fingers. “Snap” the cover back in place. e) Halogen bulb 12Volt/20Watt required. 104735 issue E ECN: 04 101 For other accessories, parts or service, please contact your local supplier(Refer to the Warranty Certificate). BULB CONTROL PANEL LIGHT REPLACEMENT I I I II I Fan On/Off Mid Speed High Sp

a. When fitting to a 50mm truss drill a pilot hole through the ceiling and into the truss. b. If securing to any other ceiling type please use appropriate fasteners and follow their instructions of use carefully. 5. For the ducting mark out and cut a O170mm hole in the ceiling. 6. Fix the ceiling bracket to the ceiling using the screws supplied. 7. Using duct tape secure the ducting to the top of the motor housing. Solid ducting, galvanized or plastic is recommended. Use flexi ducting only in di

The dust hood adjusts vertically from 29" to 49". Figure 1. Model T10117 identification. Inventory After removing the contents of the shipping package, lay them out and refer to the Parts Breakdown on the back page to inventory the components. If you need help with your new dust hood, call our Tech Support at: (570) 546-9663. Assembly Refer to Figure 1 and the Parts Breakdown illustration to aid you in the following assembly procedure. Tools Needed Qty Wrench or Socket 10, 14mm.........

ES ES 14 Panel de mando de boton electronico Este panel esta situado en la parte frontal de la campana y comprende: Pulsador para la lampara de iluminacion (ref. A). Pulsador para el apagado / encendido del motor (ref. B). Pulsador para la reduccion de la velocidad del motor (ref. C). Indicador de la velocidad del motor (ref. D). Pulsador para el aumento de la velocidad del motor (ref. E). Pulsador para la activacion directa de la velocidad TURBO del motor (ref. F). Pulsador para la temporizacio