051604 Note: The products pictured in this manual are for illustrative purposes only, intended to help install and/or operate the product. The actual product you have may be slightly different from the one illustrated herein. Thank You! Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen 10-Disc CD Changer for maxim

OTHER ACCESSORY CD Magazine Bracket (R) 1 pc. 5 Meter DIN cable (8 pin) 1 pc. Index seal sheet Self-Tapping Screw (M5 x 12) 4 pcs. Seals 1 pc. Installation Owner’s Manual guide 1pc. 1pc. 1pc. 1pc. BEFORE INSTALLING THE UNIT Transport lock screws The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation. . Caution After removing the transport lock screws, place the supplied seals over the screw holes. These s

l This unit cannot be installed on either side or up-side down. Installation in such positions will cause the mechanism 6 to malfunction. INSTALLATION The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration compensation will not be effective and vibration may cause the

The tape will keep out dust, which could cause the unit to malfunction. HORIZONTAL INSTALLATION VERTICAL INSTALLAITON 45° ANGLE INSTALLATION Set the 2 anti-vibration springs to Set the 2 anti-vibration springs to Set the 2 anti-vibration springs to position "0". position "90". position "45°". ANTI-VIBRATION SPRINGS POSITION PROCEDURE FOR HORIZONTAL INSTALLATION W/O STUDS 1 Attach a bracket to each side of the unit, using the machine screws with integral flat and lock washers (M4 x 10). In the ho

1 pc. 4 pcs. 1 pc. Self-tapping screw Seals (A) Seals (B) (M5 x 12) 4 pcs. 1 pc. 1 pc. OTHER ACCESSORIES CD Magazine Index seal sheet Installation Manual Owner’s guide 1pc. 1pc. 1pc. 1pc. BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is "locked" into place during shipment by the transport screws. Be sure to remove the screws prior to installation. . Caution . After removing the transport lock screws, place the supplied seals (A) over the screw holes. These seal

CAUTION After setting the built-in anti-vibration springs, place the supplied Seals (B) over the holes. These seals are used to keep dust, which could cause a malfunction, out of the unit. HORIZONTAL INSTALLATION Set the 4 anti-vibration springs to position "H". position "H" VERTICAL INSTALLATION Set the 4 anti-vibration springs to position "V". position "V" 45° ANGLE INSTALLATION Set the 4 anti-vibration springs to position "45°". position "45°" PROCEDURE FOR HORIZONTAL INSTALLATION Drill holes

4. Discs should be put back in their cases after use to avoid serious scratches that could cause the sound to skip. 5. Do not expose discs to direct sunlight, high humidity, or high temperatures for extended periods of time. Long exposure to high temperatures can warp the disc. 6. Do not stick paper, labels, or tape on the disc surface. 7. Do not write with any type of pen, pencil, or marker on the disc surface. 8. To minimize fingerprints and smudges on the signal surface, always try to hold th

Note: the following Discs CANNOT be used with this player : • MiniDisc • Laserdisc • CD-I, CD-ROM, DVD-ROM To load and Play a Disc Press the Power button to turn the unit ON. Select DVD mode and insert the disc (Label Up) into the disc compartment. -17 Settings and Adjustments This chapter describes how to set and how to adjust using the on-screen SETUP menu. Using the Setup Menu Using the setup display, you can do the initial setup, adjust the picture quality, and set the various outputs. You c

Sliding the switch to the on position will turn the lights on. The off position will prevent the lights from turning on at all times, and the auto position will allow the lights to turn on and off with the vehicle’s interior lighting. Refer to the Installation Manual for the wire connections. Do not leave the vehicle unattended with the dome light switch in the on position, as this could result in a discharged battery. REV FWD SOURCE VOLUME FM SELECTON OFF AUTOPAUSE HEADPH ONES I NPUT AUDI O L R