Do not use where water is microbiologically unsafe or with water of unknown quality. If bacterial contamination is present, a recognized method of water disinfection is required. Check with your public works department for applicable local plumbing and sanitation codes. Follow your local codes if they differ from the standards used in this manual. Operational, maintenance and replacement requirements are essential for this product to perform properly. The Culligan Water Tower contains replaceabl

The display will blink “SLtP” if set to English or “SLtG” if set to Metric for 3 seconds and then display the salt dosage. Adjust the setting with the “+” or “-” key (3-24 lbs.) (1-10 kgs.) Note: This option will not show if the control is set to Filter mode. Step 4 – Programming Backwash Time Press the “Status” key after programming salt dosage. The display will blink “bw” for 3 seconds and then display the backwash time in minutes. Adjust the setting with “+” or “-” key. (1-40 minutes) Program

† Contiene un control de flujo de 0.6 gpm/2.3Lpm. Para usar con un grifo separado (FT-10) en las instalaciones debajo del fregadero. NOTA: substancias reducidas no se encuentran en su agua necesariamente. El sistema y el cartucho filtrante se deben mantener de acuerdo con las instrucciones del fabricante. Instrucciones De Instalacion Y Funcionamiento Filtro de Agua Para Instalar debajo del fregadero Modelo US-550 1 Asistencia Tecnica: 1-800-645-5426 (M-F 7:30 am - 5:00 pm CST) 11/03 145765 Rev C

Test Water Feed Product Hardness Iron Hydrogen Sulfide Chlorine TDS Other Comments: Bypass Valve Bypass in Service or Bypass? Condition of bypass valve Operation OK? Control Valve Condition of Eductor (Sulfur-Cleer™) Condition of Solution Valve (Sulfur-Cleer™) Condition of Seal Pack and Brine Piston Condition of Solenoid Valve Condition of Motor: Condition of Flow Control Condition of Switches: Condition of Check Valve Condition of Compressor Output PSI Control settings Before After Check / rese

01881923 Rev. D 01/06/03 DCO# 5378 Culligan® Preferred™ Series Drinking Water Filters Installation, Operation, and Service Guide SPECIFICATIONS Operating Pressure Range: 10 - 125 psi (0.7 bar - 8.6 bar) Operating Temperature Range: 35 - 100°F (2 - 38°C) Service Flow Rate: 0.5 gpm (1.9 Lpm) Capacity: 750 gal. (2,839L) Preferred 150 1000 gal. (3,785L) Preferred 250 300 gal. (1,135L) Preferred 350 For cold water use only NSF/ANSI 42 NSF/ANSI 53 ANSI ACCREDITED CERTIFICATION PROGRAM NSF's Certificat

Failure to do so may result in cracking of the filter and water leakage. NOTE: Make certain that installation of this system complies with all state and local laws and regulations. FOR COLD WATER USE ONLY. MAINTENANCE: Contact your area retailer for replacement cartridges and pricing or call Culligan Customer Service at 800-634-1455 for the nearest dealer. Change cartridge every 2500 gallons or approximately every 12 months. Filter Installation Instructions (For copper or plastic tubing) NOTE:Sh

Fracaso de hacerlo puede resultar en grietas en el pocillo causando goteras. PRECAUCION: la arandela de caucho provee un sello hermetico entre la tapa y el pocillo. Es muy importante que la arandela se sienta correctamente en la ranura del pocillo o goteras pueden ocurrir. PRECAUCION: debido a la duracion limitada de este producto y para prevenir reparos costosos o posibles danos causados por el agua, nosotros recomendamos fuertemente que todos los pocillos plasticos transparentes de todos los p

3. Asemble todos los accesorios. Empieze a atornillar los adaptadores a la tapa manualmente. Usando una llave ajustable aprietelos firmemente. NO APRIETE CON EXAGERACION. Mas o menos una rosca debe permanecer visible. Quite las tuercas de compresion de los accesorios. 4. Mida la tapa ensemblada (como lo demostramos con una X en el diagrama) sin las tuercas de compresion y tiene que substraer 1pulgada/25mm de la tuberia de 3/4 de pulgada/19mm o 1-1/2 pulgada/38mm de la tuberia de 1/2 pulgada/13mm

For a period of TWO YEARS The control valve internal parts. The brine valve and its component parts. The salt storage container internal components. For a period of FIVE YEARS The control valve body, excluding internal parts. The fiberglass wound container(s), if so equipped*. The salt storage container(s), if so equipped. The epoxy-lined steel conditioner tank(s), if so equipped. For a period of TWELVE YEARS The conditioner tank, if it contains a plastic liner. * The tank must be protected by a

lb 870 1,150 1,750 2,530 3,550 7,000 8,800 10,800 18,500 25,000 kg 390 520 790 1,150 1,610 3,175 4,000 4,900 8,390 11,340 NOTES: 1 Service flow rates are based on 7 gpm/ft2 (26 L/m2/min) for Normal and 15 gpm/ft2 (57 L/m2/min) for Peak Flow rates. Actual service rate can vary from 2 to 20 gpm/ft2 (8 - 76 L/m2/min) depending upon the application and the raw water. 2 Backwash flow rates are based on 12-14 gpm/ft2 (45-53 L/m2/min) using 50° F (10° C) water. A different backwash rate may be required