Failure to do so may result in cracking of the filter and water leakage. NOTE: Make certain that installation of this system complies with all state and local laws and regulations. FOR COLD WATER USE ONLY. MAINTENANCE: Contact your area retailer for replacement cartridges and pricing or call Culligan Customer Service at 800-634-1455 for the nearest dealer. Change cartridge every 2500 gallons or approximately every 12 months. Filter Installation Instructions (For copper or plastic tubing) NOTE:Sh

It is recommended that, before installing a water treatment system, you have your water supply tested to determine your actual water treatment needs. This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53. Model FM-15 Substance Influe

01881923 Rev. D 01/06/03 DCO# 5378 Culligan® Preferred™ Series Drinking Water Filters Installation, Operation, and Service Guide SPECIFICATIONS Operating Pressure Range: 10 - 125 psi (0.7 bar - 8.6 bar) Operating Temperature Range: 35 - 100°F (2 - 38°C) Service Flow Rate: 0.5 gpm (1.9 Lpm) Capacity: 750 gal. (2,839L) Preferred 150 1000 gal. (3,785L) Preferred 250 300 gal. (1,135L) Preferred 350 For cold water use only NSF/ANSI 42 NSF/ANSI 53 ANSI ACCREDITED CERTIFICATION PROGRAM NSF's Certificat

This simple test can be done quickly by your dealer. The Good Water SentryTM Water Quality Monitor is another way to keep track of your system’s performance. This optional accessory checks your drinking water each time you use the special faucet, and signals when the membrane filter may need to be replaced. If the water quality of your system seems to have declined, drain the storage tank and allow the system to refill. If the problem persists, call your Culligan Man for service. INSTALLATION Th

Por mas de 60 anos, Culligan ha suplido al mundo con agua de mejor calidad. Para obtener la mejor agua posible que usted pueda desear a cualquier momento, usted debe tener confianza con Culligan. Nuestra meta es de proveer agua con una calidad lo mas alta posible, y con el mejor servicio posible para su hogar, su salud y su familia. Especificaciones para el Funcionamiento Presion: 30-125 psi / 2.1-8.6 bar Temperatura: 40-100° F / 4.4-38° C Flujo: 0.5 gpm @ 60 psi / 1.9 Lpm @ 4.1 bar Capacidad de

Do not use where water is microbiologically unsafe or with water of unknown quality. If bacterial contamination is present, a recognized method of water disinfection is required. Check with your public works department for applicable local plumbing and sanitation codes. Follow your local codes if they differ from the standards used in this manual. Operational, maintenance and replacement requirements are essential for this product to perform properly. The Culligan Water Tower contains replaceabl

The display will blink “SLtP” if set to English or “SLtG” if set to Metric for 3 seconds and then display the salt dosage. Adjust the setting with the “+” or “-” key (3-24 lbs.) (1-10 kgs.) Note: This option will not show if the control is set to Filter mode. Step 4 – Programming Backwash Time Press the “Status” key after programming salt dosage. The display will blink “bw” for 3 seconds and then display the backwash time in minutes. Adjust the setting with “+” or “-” key. (1-40 minutes) Program

For installations in Massachusetts, Massachusetts Plumbing Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of this system. The use of piercing valves is not permitted in Massachusetts. Check with your public works department for applicable local plumbing and sanitation codes. Follow your local codes if they differ from the standards used in this manual. Operational, maintenance and replacement requirements are essential for this product to perform properly. The G

Fracaso de hacerlo puede resultar en grietas en el pocillo causando goteras. PRECAUCION: la arandela de caucho provee un sello hermetico entre la tapa y el pocillo. Es muy importante que la arandela se sienta correctamente en la ranura del pocillo o goteras pueden ocurrir. PRECAUCION: debido a la duracion limitada de este producto y para prevenir reparos costosos o posibles danos causados por el agua, nosotros recomendamos fuertemente que todos los pocillos plasticos transparentes de todos los p

3. Asemble todos los accesorios. Empieze a atornillar los adaptadores a la tapa manualmente. Usando una llave ajustable aprietelos firmemente. NO APRIETE CON EXAGERACION. Mas o menos una rosca debe permanecer visible. Quite las tuercas de compresion de los accesorios. 4. Mida la tapa ensemblada (como lo demostramos con una X en el diagrama) sin las tuercas de compresion y tiene que substraer 1pulgada/25mm de la tuberia de 3/4 de pulgada/19mm o 1-1/2 pulgada/38mm de la tuberia de 1/2 pulgada/13mm