GARDENA Grass collecting bag Saves raking up the cut grass. Art. No. 4029 9. Technical Data Cutting width / Cutting height Cutting height adjustment Weight 300 (Art. No. 4020) 30 cm / 12 – 42 mm infinitely variable 8.0 kg 380 (Art. No. 4023) 38 cm / 12 – 42 mm infinitely variable 8.5 kg 10. Warranty GARDENA guarantees this product for 2 years (starting from the date of purchase). This guarantee covers all serious defects of the unit that can be proved to be material or manufacturing faults. Unde

For safety reasons, children under the age of 16 as well as persons not familiar with these operating instructions should not use this cylinder lawnmower. v Please keep these operating instructions in a safe place. Contents 1. Where to Use Your GARDENA Cylinder Lawnmower . . . . . . . . . 8 2.For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Calle Colonia Japonesa s/n (1625) Loma Verde Escobar, Buenos Aires Phone: (+54) 3488494040 info@argensem.com.ar Australia Nylex Consumer Products 50-70 Stanley Drive Somerton, Victoria, 3062 Phone: (+61) 1800 658 276 spare.parts@nylex.com.au Austria / Osterreich GARDENA Osterreich Ges.m.b.H. Stettnerweg 11-15 2100 Korneuburg Tel.:(+43) 2262 7454536 kundendienst@gardena.at Belgium GARDENA Belgium NV/SA Sterrebeekstraat 163 1930 Zaventem Phone: (+32) 27209212 Mail: info@gardena.be Brazil Palash Co

Diese Garantieleistung bezieht sich auf alle wesentlichen Mangel des Gerates, die nachweislich auf Materialoder Fabrikationsfehler zuruckzufuhren sind. Sie erfolgt durch die Ersatzlieferung eines einwandfreien Gerates oder durch die kostenlose Reparatur des eingesandten Gerates nach unserer Wahl, wenn folgende Voraussetzungen gewahrleistet sind: . Das Gerat wurde sachgema. und laut den Empfehlungen in der Gebrauchsanweisung behandelt. . Es wurde weder vom Kaufer noch von einem Dritten ver sucht,

v Only work when visibility is good. v During use do not tip the unit and do not open the rear flap. v Familiarise yourself with the surroundings of your working area. Check for possible risks which might be not audible due to the noise of the machine. v Wear sturdy shoes and long trousers to protect your legs. v Ensure you keep your feet a safe distance from the moving parts. v Make sure that there are no other people (especially children) or animals anywhere near the working area. v Always pus

Make certain that the hole cut is far enough over that it will not interfere with operators foot room. Cut hole through floor mat and floor using a round 2" hole saw (See Figure 12). After you cut the rubber mat with the hole saw pull the piece of rubber out of saw, this will make it easier to cut through the floor. (See Figure 12) 3. Install Cable / Wire Harness Boot Cover. The Boot cover will be modified, using a knife cut an "X" shaped cut across the small hole at the top. This cut will be cu

2. Remove Filler Cap. Remove Filler cap only when ready to fill hydraulic Tank with Oil. Do Not leave the Cap off and the system Open, always keep system closed when possible. Avoid any oil contamination. (See Figure 29) 3. Avoid Hydraulic Contamination by filtering the Hydraulic Oil while filling the Hydraulic Tank. Filter bug- gies or carts are commercially available for Hydraulic system cleanup and Oil transfer. These consist of high capacity filter, a Circulating Pump, a Drive Motor and hose

Alamo Group is not responsible for modifications to the MountKit to accommodate these differences. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas 78155 210-379-1480 © 2005 Alamo Group Inc. TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment

40, D-89079 Ulm, hereby certifies that, when leaving our factory, the unit indicated below is in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards. This certificate becomes void if the unit is modified without our approval. Typ: Art.-Nr.: Type: Art. No.: Type : Reference : Typ: Art. nr.: Typ : powerCut Art.nr. : 2404 Modello: Art. : Tipo: Art. N.: Tipo: Art. N.: Type: Varenr. : F Certificat de conformite aux directives europeennes Le constructeur

Remove RH Rear Tire and Wheel (If Required, See Assembly Drawings sent with unit). Use proper Floor jack to lift the RH Rear Wheel, Support the tractor with proper jack stands rated appropriately for the tractors weight. The RH rear tire and wheel should be removed for this installation by using the Axtreme Boom (Asy. Man) 07/06 © 2006 Alamo Group Inc. Section 4 - 4 5. Install the new mount brackets to the tractor frame. (If Required, See Assembly Drawings sent with unit) The tank mounting brack