Always wear eye and hearing protection when operating this unit. WARNING! Part Number 62719-94310 Rev. 11/06 Introduction General Safety Instructions Attention Statements The Shindaiwa 231-series of hand-held power tools has been designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. Shindaiwa’s high-performance engines represent the leading edge of 2-cycle engine technology, delivering exceptionally high power with remark

Always wear eye protection, gloves and a respirator when operating this unit. Part Number 80702 Rev. 4/02 Shindaiwa Inc. 11975 S.W. Herman Road Tualatin, Oregon 97062 Telephone: 503 692-3070 Fax: 503 692-6696 2002 Shindaiwa, Inc. Part Number 80702 Revision 4/02 Shindaiwa is a registered trademark of Shindaiwa, Inc. Specifications subject to change without notice. Printed in Brazil Introduction This manual contains information for the proper assembly, operation and care of your SP518 sprayer. Ca

LE242 IMPORTANT Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged or missing information labels. New labels are available from your local authorized Shindaiwa dealer. Figure 3 Product Description Using the accompanying illustrations as a guide, familiarize yourself with this unit and its various components. See Figure 4. Understanding your unit helps ensure top performance, long service life, and safer operation. LE2

WARNING! Before performing any maintenance, repair or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance work. WARNING! Non-standard parts may not operate properly with your unit and may cause damage and lead to personal injury. NOTE: Using non-standard replacement parts could invalidate your Shindaiwa warranty. Muffler This unit must never be operated with a faulty or missing spar

REQUISITOS DE MANTENIMIENTO Y REPARACION Usted es responsable del uso y mantenimiento correctos del motor. Usted debera conservar todos los comprobantes y registros de mantenimiento que cubran la realizacion de mantenimiento regular en caso de que surjan preguntas. Estos comprobantes y los registros de mantenimiento deberan ser transferidos a cada propietario subsiguiente del motor. Shindaiwa Corporation se reserva el derecho a negar la cobertura de garantia si el propietario no ha mantenido cor

Esta garantia sobre normas de emision rige para todos los estados, excepto para el Estado de California. Para las piezas listadas en PIEZAS CUBIERTAS, el Distribuidor autorizado por Shindaiwa Corporation efectuara, sin costo para el propietario, los diagnosticos, reparaciones o reemplazos necesarios de cualquier componente defectuoso en relacion con las emisiones para asegurar que el motor cumpla con las reglamentaciones de la EPA de EE.UU. aplicables. COBERTURA DE LA GARANTIA DEL FABRICANTE Cua

Como propietario/operario, usted no tardara en comprobar que Shindaiwa es la unica maquina en esta clase! Pagina Contenido Shindaiwa Inc. se reserva el derecho de realizar cambios a sus productos sin previo aviso, y sin la obligacion de hacer modificaciones a maquinas fabricadas previamente. .IMPORTANTE! La informacion contenida en este manual describe unidades disponibles a la fecha de su publicacion. Pagina .ADVERTENCIA! Las emisiones emitidas por el tubo de escape de este producto contienen s

Remove both screws from the handle. 2. While spreading the handle at the mounting hole, position the handle on the outer tube as shown. 3. Reinstall the two mounting screws in the handle, but do not tighten them at this time. NOTE: The handle is recessed to receive the hex nuts. 4. Locate the handle at the best position for operator comfort (usually about 10 inches ahead of the throttle assembly). 5. Secure the handle by tightening the mounting screw and the adjustment knob screw. Hex Nut Hex Nu

Figure 24 50-Hour Maintenance Lubricate the Flexible Shaft. Lack of lubrication will cause rapid wear to the flexible shaft and also to the shaft tube liner, resulting in increased vibration and greatly decreased service life. Remove and lubricate the flexible shaft as follows: Refer to Figure 27: 1. Loosen the gearcase clamp screw. 2. Remove the gearcase index screw. 3. Slide the gearcase and shield assembly from the shaft tube. 4. Pull the flexible shaft from the shaft tube assembly, and clean

Primer Bulb Figure 10 CAUTION! Do not pull the recoil starter to the end of the rope travel. Pulling the recoil starter to the end of the rope travel can damage the starter. 2. Press the primer bulb until fuel can be seen flowing in the transparent return tube. IMPORTANT! The primer system only pushes fuel through the carburetor. Repeatedly pressing the primer bulb will not flood the engine with fuel. WARNING! The cutting attachment may rotate when the engine is started! 3. Set the choke lever t