circulating air passageways of the appliance be kept clean. • Due to high temperatures, the appliance should be located • DO NOT use this room heater if any part has been under out of traffic and away from furniture and draperies. water. Immediately call a qualified service technician to • Children and adults should be alerted to the hazard of inspect the room heater and to replace any part of the high surface temperature and should stay away to avoid control system and any gas control which has

The National Fuel Gas Code, ANSI Z223.1 defines a confined space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the aggregate input rating of all appliances installed in that space and an unconfined space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8m3 per kw) of the aggregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed, t

Nunca use una llama expuesta para inspeccionar fugas. El aparato debe desconectarse de la tuberia a la salida de la valvula, y sellarse cuando se pruebe la presion de gas. .Nunca pruebe la presion de gas estando el calentador conectado; la valvula se danara! Una union para valvula de gas y para la conexion de tierra deben de instalarse en la linea de gas contracorriente de la valvula para ayudar durante su servicio. Se requiere segun el National Fuel Gas Code que una linea de gotera sea instalad

9. Open tees should not be used in the flue pipe. 10. Appliance must not be connected to a chimney flue that is servicing a separate solid-fuel burning appliance. For proper venting, do not attach a 90° elbow directly to draft diverter. If possible, attach 2 feet (.6m) of straight vent pipe before an elbow is used. Use 45° elbows if possible. Uninsulated single-wall metal pipe shall not be used outdoors in cold climates for venting gas utilization equipment. Ventilation and Combustion Air Room h

If, after reading the following information, you feel you still need more information, please contact your gas supplier. Propane (LP-Gas) is a flammable gas which can cause fires and explosions. In its natural state, propane is odorless and colorless. You may not know all the following safety precautions which can protect both you and your family from an accident. Read them carefully now, then review them point SAFETY INFORMATION FOR USERS OF LP-GAS • Do not operate electric switches, light matc

— Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. — Installation and service must be performed by a qualified installer,

Now, use the following Steps to complete installation of the SOK-1. 1. Using the inner and outer boots as hole templates, mark and drill four (4) 1/8” (3mm) diameter holes in the inner shield and four (4) 1/8” (3mm) diameter holes in the cabinet side. 2. Locate and cut a 6 3/4” square opening through wall. 3. Attach furnace to wall (see Attaching Furnace to Wall). 4. With furnace in place, after checking alignment of side outlet opening in wall and furnace, place the 9 3/8” x 9 3/8” side outlet

Attach vent cap to outside mounting plate with three (3) 10 x 1/2” screws. 4. Reassembly and resealing vent-air intake system is completed. Installing a Vent Near a Window Ledge, Other Type of Projection or on Siding (vinyl, aluminum, etc.) Direct vent furnaces are designed to be installed on a uniform outside wall. When the wind comes from any angle (up, down or from either side), it must hit the vent cap equally over both the air inlet and the flue outlet portions of the vent. Any wall project

(Strong winds, dirty pilot and low pressure will reduce readings.) Piezo Pilot Ignitor Instructions Depressing the button completely causes a spark to occur at the pilot. This is a substitute for a match which requires opening the pilot hole cover. To light the pilot, it is important that the electrode be 1/8" (3mm) from the thermopile. The spark must occur at the point the burner flame hits the thermopile. The end of the electrode will be red hot with the pilot on. On a new installation with ai

In case of regulator malfunction, the six (6) (1.83m) feet distance will reduce the chance of gas entering the vent cap. Location of Furnace Pick a location on an outside wall with a clear space of 28" (711mm) high by 49" (124cm) wide in the room. Locating Wall Opening The furnace is to be located on an outside wall. Locate wall studs so that wall opening will be located between wall studs. The wall studs can be used for attachment of wall mounting bracket. The wall opening required as shown in