Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
NetServer LXr Pro8 Inside
Reserved
Firmware
Service Reference Label
6 5 4 3 2 1 0
Clear CMOS Enable
Boot Order
BIOS Recovery Enable
1.
CD-ROM (SCSI Address 0)
*
(See Panel of this label)
2.
Flexible Disk
*
Boot Block BIOS:
3.
Internal SCSI Drives
6 5 4 3 2 1 0
Default:
Flash Enable / Protect
4.
Optional SCSI Extender Drawer
Clear CMOS Protect
Key
5.
PCI P1
Main BIOS:
BIOS Recovery Protect
•
•
Check by
Protect / Flash Enable
(See Panel of this label)
visual inspection
•
•
•
•
Check with
Diagnostic Assistant
6 5 4 3 2 1 0
12.
PCI P8
JP8 (Reserved)
* Default: included in boot order. To check or change,
press to enter Boot Menu when pr
E S C
ompted during
System Board
CON F
Power On Self-Test.
Processor
Default: included in boot order. To check or change,
press
C t r l + C to run SCSI Setup Utility when
JP9
Troubleshooting
prompted after memory count stage of boot.
Caution:
JP10
ROM Setup
Operating a CPU chip on an incorrect Processor Board, or
CPU BUS A
CPU BUS B
Check
(see board picture).
Press
F 2 to enter Setup when prompted during
at a lower or higher speed, or at incorrect voltage may result
A2
A1
B2
B1
PCI BUS 0
PCI BUS 1
Power On Self-Test.
in unreliable operation -- or cause catastrophic or hidden
Check that system matches one of these configurations.
damage to the chip.
P1
P2
P3
P4
P5
P6
P7
P8
All processor slots must be filled.
Memory Test
Repairs due to unauthorized jumper modification or use
Total Number
Full Test: Press D during memory count stage of boot.
of incorrect chip and board combinations are not covered
of CPU Chips Board in
Board in
Board in
Board in
Clear CMOS
under the warranty. CPU chips supplied and warranted by
in System
Slot A2
Slot A1
Slot B2
Slot B1
1 Ensure jumper CONF 0 on System Board is in
HP for HP NetServers have an HP label.
2 CPUS
Terminator
Processor
Terminator
Terminator
"Enable" position (see Panel on this label)
2 Power up system while holding F2 down
4 CPUS
Terminator
Processor
Terminator
Processor
3 Keyboard LEDs flash when done
6 CPUS
Processor
Processor
Terminator
Processor
002-52460, Rev B
4 Power down system
8 CPUS
Processor
Processor
Processor
Processor
5 Reset jumper to "Protect" position
Boot Status
6 Power up system (takes up to 2 minutes)
0 1 2 3 4 5 6 7
Not Replaceable
Reserved
Check that all processors, DIMMs, and drives are connected
and responding with the Diagnostic Assistant (select Hardware
BIOS Recovery from Boot Block
Inventory).
1 Ensure jumper CONF 0 on System Board is in
Upper
Lower
Video Card in P1
Connector
"Enable" position (see Panel on this label)
Processor
Processor
JP1
Check BIOS version with Diagnostic Assistant (select "Hardware
Reserved
Printer
Unused
2 Put diskette copy of BIOS file in flexible disk drive
Inventory").
(Speaker)
3
F 3
Power up system while holding down
JP4
EXT opening in rear panel
Unused
Mouse
Check operation with Diagnostic Assistant (select "Quick Tests"
(Reset Switch)
4 Keyboard LEDs flash when done
Keyboard
then "Run All Tests").
5 Power down system
Diagnostic Assistant
Serial B
6 Reset jumper to "Protect" position
Unused
disk pouch
Serial A
7 Power up system (takes up to 2 minutes)