Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
HP NetServer LC 2000 & LC 2000r Technical Reference Card
HP Product No. D8514-80201, REV B, Sept. 1999
D SCSI Hot-Swap HDD Configurations
E Mass Storage Cabling
Built-in SCSI Terminator
HDD Slot SCSI ID
6
9
9
9
Cables
8
5
8
8
8
IDE CD-ROM Drive
1 FDD Cable
4
3
3
1
2
3
4
5
2
2
3
2
2
2 Unterminated SCSI Cable from
2
1
1
System Board to Hot-Swap Bay
0
0
1
(See Notes 1 & 2).
0
0
Optional
4
Non-Hot-
6 LP
3 HH
1HH-4LP
2 LP-HH-2LP
Swap Mass
Front Panel
3
3 Terminated SCSI Cable from System
Storage Units
HDD Slot
Connector
Board to Common Tray Devices.
Hot-Swap Mass Storage
DO NOT CONNECT TO HOT-SWAP
6
9
9
3
Configurations
Flexible Disk
BAY. (See Notes 1 & 2)
5
8
• Ensure hot-swap drives are
IDE CD-ROM
1
Drive
4
3
installed in lowest (pedestal)
Connector
4 IDE CD-ROM Cable
2
3
2
or left-most (rack) slot first.
5
Front Panel
2
• Use only HP Ultra-2 (LVD)
SCSI B
Display
5 Control Panel Cable
0
0
Connector
1
SCSI 3.5-inch HDDs.
2
Alternating
2HH-2LP
• You may mix or match Low
SCSI A
Hot-Swap
6 SCSI Cable for Hot-Swap
HH-LP
Profile (LP–1-inch) and Half-
Connector
6
Mass Storage
Height (HH–1.6-inch) HHD.
Drives
Note 1: Connectors on cables and
• For rack-mounted models,
Flexible
6
2
3 must be plugged into the
rotate diagrams 90˚ clockwise
Disk Drive
Connector
correct connector, as shown
on labeled cable-ends.
Key
1.6˝ Half-Height (HH) drive
SCSI ID
Note 2: Cables
2 and
3 are not
Shown Here
interchangeable. Cable
2 is
1˝ Low Profile (LP) drive
System Board C
Fan Module
Mass Storage
unterminated, cable
3 is
.5˝ Drive Spacer
(Removed)
Cage
terminated. Data corruption
will occur unless cables are
connected as shown.
Note 3: Further details in the
Installation Guide.
F Power Supply Cabling
G
IDE CD-ROM Drive
Service Information
System Board C
Fan Module (Removed)
Non-Hot-Swap Mass
Storage Units
Electronic Support Services
Flexible Disk Drive
• Internet Web Pages http://www.hp.com/netserver
P4
Front Panel
• Internet FTP ftp://ftp.netserver.hp.com
Audience Assumptions
Display
P3
• CompuServe Library GO HPPC
This Technical Reference Card is for
trained service personnel. Hewlett-Packard
Hot-Swap Mass
• HP Navigator CD
P5
Company assumes you are qualified in the
Fan Module
Storage Drives
Support Questions
servicing of computer equipment and trained
Power Connector
P6
in recognizing hazards in products with
P1, P2, and P3 are
• HP-Authorized Reseller
connected to power
hazardous energy levels.
P
Optional
4
supplies below/behind
• CompuServe Discussion Forum GO HPPC
Redundant Power
P4 and P5
Electrostatic Discharge
• US / Canada Phone Support 1-208-331-2767
P
Supply Connectors
To avoid catastrophic or hidden damage to
5
P2
• Europe Phone Support (+31-20) 581-3330
components, wear a wrist strap and use a
P1
(Netherlands)
static-dissipative work surface connected to
Mass Storage
the chassis when handling components. Use
P1
P4
HP has offices in over 100 countries.
Power Connector
an antistatic service kit, such as 3M
Check your local telephone directory.
8501/8502/8505 or equivalent.
P
P2
4
This information is subject to change without
P5
notice and is provided without warranty.
P
5
P3
© copyright 1999, Hewlett-Packard
For additional information, see other side.