Iniciar sesión:
Clasificado: Nombre ↑   Descargas   Tarifa   Tamaño ↑  
Descargado: 5   Tamaño del archivo: 637 kb   Fabricar: Enviro  
Categoría: Placa
@name

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE PELLET STOVE EF THERMO 28 OWNER’S MANUAL ........ PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. Contact your building or fire officials about restrictions and installation inspection requirements in your area. 50-877 Table of Contents Introduction.....................................................

Descargado: 16   Tamaño del archivo: 2 mb   Fabricar: Enviro  
Categoría: Placa
@name

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE PELLET STOVE Mini TECHNICAL MANUAL PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH Contact your building or fire officials about restrictions and installation inspection requirements in your area. 50-1221 Table of Contents Introduction....................................................................

Descargado: 1   Tamaño del archivo: 1 mb   Fabricar: Enviro  
Categoría: Placa
@name

This is due to back-pressure in the exhaust, caused by the air flow around the house. Text Box: 5.0” Text Box: 10.812” Text Box: 11.938” Text Box: 16.625” Text Box: 1” Text Box: THROUGH WALL INSTALLATION FREESTANDING INSIDE VERTICAL INSTALLATION 1. Choose a stove location that is ideal. See the section Deciding Where to Locate Your Pellet Appliance. 2. Place a non-combustible hearth pad where necessary. 3. Place the unit on the hearth pad and space it in a manner so when the pellet vent is insta

Descargado: 0   Tamaño del archivo: 1 mb   Fabricar: Enviro  
Categoría: Placa
@name

12. 120°F (49°C)-N/C TEMPERATURE SENSOR (IGNITER SHUT DOWN SENSOR) This sensor (mounted on the exhaust channel) will turn the igniter off when the exhaust channel temperature reaches 120°F (49°C). 13. IGNITER Is a heating element used to ignite the fuel? When the start up switch is activated, the igniter is has power going to the igniter when the switch is in the manual position. Air passes through the igniter tube, which becomes super heated drying the fuel and then igniting the fuel through co

Descargado: 0   Tamaño del archivo: 4 mb   Fabricar: Enviro  
Categoría: Placa
@name

AFGS1095 CONTENTS INSTALLATION Safety Notices General Information Contents List & Part Identification Important Notices Statutory Requirements Certification Technical Data Gas Fire Dimensions Installing The Stove Preparation of the stove Stove Location Shelf Clearances Flue System Fitting The Flue Spigot And Blanking Plate Rear / Top Flue Options Connecting The Gas Supply Pressure Test Sequence Fitting & Arranging The Coals Fitting & Arranging The Logs NG Fitting & Arranging The Logs LPG Install

Descargado: 9   Tamaño del archivo: 1 mb   Fabricar: Enviro  
Categoría: Placa
@name

Remove the slider rod (short rod with knob and nuts) and the two nuts from their package and open the left side panel. 2. Remove the knob and outer nut from the knob. Push the rod through the hole in the slider. Place the lock nut on the rod and tighten, leaving a 1/32’ gap between the slider and one of the nuts. 3. Make sure the slider moves freely. Close the side panel and tighten screws after placing the rod through the panel. Screw the knob onto the slider. OPERATION - On the low heat output

Descargado: 10   Tamaño del archivo: 2 mb   Fabricar: Enviro  
Categoría: Placa
@name

The throat plate should be removed and checked monthly, and any debris stripped off. Similarly, clean the upper surface of the firebox. Refer to page 16 for instructions on the throat plate removal / inspections. OUTER FINISH The outside finish of the appliance is a durable high temperature paint. It is best cleaned by brushing down with a clean shoe brush. Do not allow moisture to remain on the appliance whilst cold or surface rust may form. The high temperature paint should not require attenti

Descargado: 1   Tamaño del archivo: 699 kb   Fabricar: Enviro  
Categoría: Placa
@name

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE Wood Stove 2100 Freestanding BY: SHERWOOD INDUSTRIES LTD OWNER’S MANUAL Contact your local building or fire officials, or the authority having jurisdiction about restrictions and installation inspection requirements in your area. PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS WOOD BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. This heater meets the U. S

Descargado: 0   Tamaño del archivo: 997 kb   Fabricar: Enviro  
Categoría: Placa
@name

An ENVIROFIRE dealer will be happy to assist you in obtaining information with regards to your local building codes and installation restrictions. The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive chimney pressure, it is very important to ensure that the exhaust system be sealed and airtight. This unit is designed to burn pelletized wood fuel only. Do not use any other type of fuel, this will void any warranties stated in this manual. THE USE OF C

Descargado: 0   Tamaño del archivo: 2 mb   Fabricar: Enviro  
Categoría: Placa
@name

February2005 3 Parts Diagram - Steel .............................................................................................................................. .................................................... February2005 3 Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the fo





Categoría