1345315 ©Delta International Machinery Corp. 1993 ▲ ▲▲DELTA INSTRUCTION MANUAL TABLE OF CONTENTS SAFETY RULES..............................................................3 INTRODUCTION..............................................................3 UNPACKING.................................................................3 ASSEMBLY INSTRUCTIONS Assembling Cyclone Separator To Fan Housing................................4 Assembling Legs To Blower Assembly...............................

The smaller the gauge number, the heavier the cord. 15. SECURE THE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury. 16. FEED THE WORKPIECE AGAINST THE DIRECTION OF THE ROTATION OF THE BLADE, CUTTER, OR ABRASIVE SURFACE. Feeding it from the other direction will cause the workpiece to be thrown out at high speed. 17. DON’T FORCE THE WORKPIECE ON THE MACHINE. Damage to the machine and/or injury may result. 18. DON’T OVERREACH. Lo

Water) Maximum Hose Velocity PPM Bag Area in Sq. Ft. dBA " Hose Size Drum Size 50-180 1 HP 1 Ph. 115/230 60-3450 700 4Vz" 5131 19.0 83. 5" x 60" 55 Gal. 50-181 2 HP 1 Ph. 230 60-3450 1100 8 W 5600 19.0 85 6" x 60" 55 Gal. 50-182 3 HP 3 Ph. 230/460 60-3480 ! 1300 10» 6619 50.0 84 6" x 60" 55 Gal. / - - ’ . ■' - ' • ■" DATED 11-28-94 " . - PART NO. 410-06-651-0001 © Delta International Machinery Corp. 1994 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR SERVIC

Cutters 09-128 & 09-137 are counterbored to fit Stub Spindle. Cutters are shown 3/8 size. 1/2 Lb. each. 09-100 09-101 09-102 09-103 09-106 1/2" Cove 5/16" Cove 1/8" & 3/8" 1/4" & 1/2" 90° 5/16" Qr. Rd. 3/8" Bead Qr. Rd. Qr. Rd. V-Groove 1/4" Bead 09-109 09-111 09-112 09-113 09-114 1/4" Flute Stile with Rail with Drop Leaf Drop Leave 1/4" Groove 1/4" Tongue Bead Cove 09-115 09-116 09-117 09-118 3-Bead Clover 1/2" Rad. 3/4" Qr. Rd. Cove Leaf Base Shoe 09-120 09-121 09-125 09-126 09-128 Ogee Female

In a severe dirty operation, the blower impeller should be cleaned with a wire brush to prevent an accumulation of foreign matter that could result in blower unbalance After cleaning impeller, inspect for possible cracks or excessive wear, which can cause unbalance. DO NOT USE AN IMPELLER THAT IS CRACKED OR EXCESSIVELY WORN; REPLACE IT WITH A NEW IMPELLER. MOTOR MAINTENANCE: Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. shou

Fire resistant aluminum foil lined fiberdrum. 24* diameter x 31 "high. 14 lbs. No. 50-311 Drum DoUey. 5-wheel. Accommodates 55-gallon capacity fiber or metal drum. Adds portability to your dust collector system. No. 50-225 2' Diameter x 3f Dust Bag. 22 sq. ft. filter area. New 3-dimensional weave for improved dust retention. With drawstring to fit standard 55-gallon drum. For use with No. 50-1801 HPaod 50-181 2 HP Dust Collectors for planer chip pick up. Also No. 50-1801 HP Unit when major u

Current models have stamped sheet metal blower housings. D - When screw requires servicing install at 100 inch lbs 10 REPLACEMENT PARTS 50-185 BAG ASSEMBLY ----------- (OPTIONAL FOR 50-180 & 50-181 - STANDARD FOR 50-182) REF № PART NUMBER 50-185 1 50-188 2 410-06-027-00001 3 410-06-105-0001 4 50-195 OESCRIPTIQN DRUM MOUNTED DUST BAG, CONST OF: HOSE, INCL; CLAMP - 6" HOSE SLEEVE DUSTBAG NOT SHOWN ASSEMBLED NOTE: THE NECK OF THE BAG MUST BE CLAMPED TO THE DRUM USING A STANDARD 55

Indica una situación potencialmente riesgosa, que si no es evitada, podría resultar en la muerte o APELIGRO: A ADVERTENCIA: lesiones serias. APRECAUCIÓN: Indica una situación potencialmente peligrosa, la cual, si no es evitada, podría resultar en lesiones menores o mode-radas. PRECAUCION I Usado sin el símbolo de seguridad de alerta indica una situa-ción potencialmente riesgosa la que, si no es evitada, podría causar daños en la propiedad. PROPOSICIÓN DE CALIFORNIA 65 fiTJ M Algunos tip

Se requieren dos o más personas para levantarla. CÓMO COLOCAR LAS RUEDAS 1. Invierta la base (A) (Fig 1). 2. Alinee los orificios del conjunto de las ruedas (B) con los de las placas de la base. Coloque una arandela plana pequeña de 8 mm (5/16") sobre un tornillo de cabeza hexagonal de 8 mm x 19,1 mm (5/16" x 3/4"). Coloque el tornillo a través del orificio en el conjunto de la rueda y enrósquelo en el orificio de la base. Coloque los conjuntos de la otra rueda de la misma forma. 3. Ajuste

12A 4. Inserte la varilla (A) Fig. 12B en el orificio del soporte (B). Asegurese de que ninguno de los cuatro extremos de la bolsa este doblado. 5. Coloque el extremo abierto de la bolsa de filtro dentro de la ranura superior del tambor del recolector de polvo hasta que quede seguro y sellado. (De manera similar a como se inserto el anillo interior de la bolsa inferior, Fig. 9. Sera necesario doblar y plegar el anillo interior de retencion para bolsa a fin de que calce en su lugar. 6. La Fig. 12