The spokes, handle and hub on your safe should be cleaned only with a soft, damp cloth. No abrasives or chemicals of any kind should be used. loCking Bolts The tolerances between your locking bolts and the safe body and door are very tight. Because they fit so tightly, it may be necessary from time to time to place a small amount of Teflon® lubricant on the bottom of each bolt with the bolts in the extended position. mirror interior If your safe is equipped with an interior mirror on the back pa

DO NOT HOWEvER, ASSUME THAT ANY SAFE IS IMPENETRABLE — IT IS NOT! A KNOWLEDGEABLE THIEF CAN GET INTO ANY SAFE IF GIvEN THE APPROPRIATE TOOLS AND ENOUGH TIME. Your safe is a deterrent and a delaying device. You can make it even more effective by placing it in the right location and anchoring it to the floor and wall. Browning ProSteel fire safes offer similar protection against fire. They are fire-resistant, not fireproof. DO NOT ASSUME A FIRE-RESISTANT SAFE WILL WITHSTAND ANY AND ALL FIRES — IT

Your shelves are held in place by several clips that secure them to four “tracks” on the safe interior. Some are above the shelves and some are below. To remove a clip, squeeze it together with hand pressure or adjusting the hinges. pliers and lift up. The shelves can be relocated along this track by simply relocating the clips to the desired shelf location. To replace a clip, insert the top lip of the clip into the appropriate slot in the track, squeeze the clip together and insert the bottom l

Changing the ComBination Your combination of the S & G® Mechanical Lock is pre-set at the factory. Changing the combination will void your lock warranty. If you must change the combination for some reason, contact a certified locksmith to do this for you. keyloCk The keylock in your combination dial is used to lock the dial only. This is a convenience feature that allows you to lock your dial so that it will not accidentally rotate and lock while you are moving items into or out of your safe. Th

4 Make sure the replacement bulb is installed correctly. (If you have questions contact customer service.) 6 Remove soft cloth from new replacement bulb before putting lens cover back on. 7 Replace lens cover with a clockwise motion. Care safe Body All Browning ProSteel safe paint finishes are designed for indoor use only. Use a damp rag to wipe down the surface of the safe. If something other than water is needed, a very mild soap solution may be used. However, only water should be used around

6 Use a 2" wood bit to drill though the fire-resistant insulation. Do not attempt to drill through the steel safe body with the wood bit. 7 Reposition the safe on your centerline marks against the wall and mark the hole centers on the wall of the house. 8 Use a 5/16" wood bit to drill the pilot holes through the sheet rock and stud. Next install 3/8" x 3." lag bolts through a 1." diameter steel washer through the safe body and into the stud. Tighten all anchor bolts. 9 Fill the 2" holes in the s

Use a 2" wood bit to drill though the fire-resistant insulation. Do not attempt to drill through the steel safe body with the wood bit. 3 Use a ." high-speed bit designed for drilling metal to drill through the steel safe wall. Once you have drilled though the fire-resistant material and safe body, mark the center of your holes on the wall. 4 Remove the safe and use a 3/8" masonry bit to drill the anchor holes. Reposition the safe over the holes and install the expansion anchors and washers thro

No maintenance is required for the electronic lock, other than changing the battery by following the directions in the lock instructions. 14 You should immediately change the combination of the electronic lock from the factory default code. The lock instructions outline the process to program a new electronic lock combination. IMPORTANT: Record the combination you select, as the factory will not have any record of the combination you choose. If you forget the combination on your electronic lock

5 Open and close the door several times to make sure it swings smoothly. IMPORTANT: Hardened steel ball bearings are located below the hinge pins within the hinge housing. Do not lose these bearings while the door is off of the safe. Care should be taken not to damage the paint while removing or re-installing the door. anChoring your safe to the floor Placing your safe on a concrete floor and anchoring it to the floor and wall behind it provides the maximum protection for your valuables. Many co

failure To follow This warning could resulT in serious injury or deaTh. Some considerations that need to be addressed when moving your safe into your home are: • The load your floors and stairs will bear. • Tile or other floors that could be damaged. • Doorways or furniture that could be damaged. • Stairs or corners you will need to navigate. remoVing the safe door Most Browning ProSteel safes have external hinges (except Compact Series safes which feature a non-removable, internal hinge design)