8 Appuyer sur le bouton DTS et le maintenir enfonce (8 s) pour afficher le menu Declenchement WatchDog en %. Maintenir le bouton enfonce pour pouvoir regler le declenchement de WatchDog a 30, 40, 50 ou 60 % de la pression de consigne en cours sur le pulverisateur. Relacher le bouton DTS des qu’apparait le % voulu. La valeur par defaut est de 50 %. 9 Appuyer un bref instant pour passer a SOFTWARE REV Menu auxiliar: Modos de Datos almacenados y WatchDog™ de proteccion de la bomba 5 Pulse brevement

If plug will not fit in outlet, have grounded outlet installed by a qualified electrician. Do not use an adapter. Power Requirements • 100-120V units require 100-120 VAC, 50/60 Hz, 15A, 1 phase. • 230V units require 230 VAC, 50/60 HZ, 10A, 1 phase. Extension Cord Use an extension cord with an undamaged ground contact. If an extension cord is necessary, use a 3-wire, 12 AWG (2.5 mm2) minimum. Pails Solvent and oil/based fluids: follow local code. Use only conductive metal pails, placed on a groun

10. Leaking around throat packing nut which may indicate worn or damaged packings. 10. Replace packings; see pump manual. Also check piston valve seat for hardened paint or nicks and replace if necessary. Tighten packing nut/wet-cup. 11. Pump rod damage 11. Repair pump. See pump manual 310643 or 310894. 12. Low stall pressure 12. Turn pressure knob fully clockwise. Make sure pressure control knob is properly installed to allow full clockwise position. If problem persists, replace pressure transd

. 248684 . . 248685 . . 248686 . . GMAX ll 5900 248687 . . 248688 . . 248689 . . 248690 . . GMAX II 5900HD 248699 . . GMAX ll 5900 Convertible 248691 . . 248692 . . 248693 . . 248694 . . 248695 . . 248696 . . 248697 . . 248889 . . 248890 . . GMAX ll 7900 248700 . . 248701 . . 248702 . . 248703 . . TexSpray 5900 HD Convertible 255630 . . 255631 . . 255954 . . TexSpray 7900 HD 255632 . . ti5474a ti5475a ti5447a ti11418a 310893 311046 311861 310894 309640 Manual Conventions Manual Conventions WARNI

Save these instructions. See page 2 for part numbers and maxumum working pressure. Model 12004X Models 12004 and 12005 Model 12006 309739D Models Models Pistol Grip, Base Seal Pistol Grip, Tip Seal Part Number Model Description 2500 psi (17.2 MPa, 172 bar) maximum working pressure C27020 12004 Standard base seal C27031 12004X Two stage, easy pull C27067 12005 Balanced piston Part Number Model Description 2000 psi (13.79 MPa, 137.9 bar) maximum working pressure C27078 12006 Pistol Grip, Tip Seal

Then loosen it completely. Clear tip/nozzle or hose. Trigger Lock Always engage trigger lock when you stop dispensing to prevent gun from being triggered accidentally by hand or if dropped or bumped. To engage trigger lock, release trigger and rotate lock downward. See Fig. 1. To disengage trigger lock, rotate it upward. See Fig. 2. If material hose will be suspended by a hanger or tool balancer, route hose through the suspension device before securing each end of material hose. To help prevent

Check them carefully for damage or wear, replacing parts as needed. For best results replace the original parts with new parts in repair kits. Prior to assembly, lubricate all seals and o-rings with PARKER-O-LUBE or an equivalent lubricant. 1. Connect needle (8) and stop nut (2) to yoke (1). 2. Secure yoke (1) in soft jawed vise. Lock stop nut (2) against yoke. ti4043a 3. Insert needle (8) into packing nut (5). 4. Push three seal needles (6) in packing nut (5) using soft rod or dowel. Orient as

12. While holding adapter stationary, screw collar (17) and nozzle (18) into adapter. Do not overtighten collar. 13. Reconnect flow gun to material supply line. 14. Turn on material supply line. 15. Return flow gun to normal operating condition. 309739 11 Parts 12 309739 Parts Models 12004 & 12004X 13 1 2 5 3 6 4 7 11 23 12 16 9 10 8 15 14 17 18 21 19 20 Item Part No. Description Qty 1 C27052 YOKE 1 2 100284 NUT, hex (model 12004) 1 C19284 NUT, hex (model 12004-X) 1 3 C27061 SCREW, adjustment 1

32 311360D Technical Data Technical Data Model 100 - 120V, A, Hz 220 - 240V, A, Hz Generator Minimum W Motor HP (W) Cycles per gallon (liter) Maximum Delivery gpm (lpm) Maximum Tip Size Fluid Outlet npsm 1 Gun 2 Guns 695 14.8, 50/60 9, 50/60 5000 1.75 (1300) 226 (60) 0.79 (3) 0.029 0.019 1/4 in 795 15, 50/60 10, 50/60 5000 2.00 (1490) 195 (52) 0.95 (3.6) 0.031 0.021 1/4 in 1095 15, 50/60 10, 50/60 5000 2.20 (1640) 123 (33) 1.1 (4.1) 0.033 0.023 1/4 in Mark V N/A 10, 50/60 5000 2.20 (1640) 110 (2

Disengage gun trigger safety. 5. Hold gun against grounded metal flushing pail. Trigger gun and increase fluid pressure 1/2 turn. Flush 1 minute. 6. Inspect for leaks. Do not stop leaks with hand or a rag! If leaks occur, perform Pressure Relief Procedure, page 8. Tighten fittings. Perform Startup, steps 1 - 5. If no leaks, proceed to step 7. 7. Place pump in paint pail. 8. Trigger gun again into flushing pail until paint appears. Move gun to paint pail and trigger for 20 seconds. Set gun safety