: Arranque el motor. : Coloquese la correa sobre el hombro. Nunca tire las piezas recortadas en Posicion de trabajo Sujete el mango de control con la mano derecha y el tubo de mando con la izquierda. Extienda el brazo izquierdo a la posicion que le resulte mas comoda. La posicion de trabajo mas comoda es mantener la herramienta a un angulo de 60°, pero cualquier angulo mas pequeno puede usarse segun el caso. Corte transversal 390BA052 KN el basurero domestico – .estas pueden convertirse en abono

If there is any damage, do not use until damage is repaired by your authorized service dealer. S Do not use the unit if the switch does not turn the unit on and off properly. Have the unit repaired by your authorized service dealer. S Do not use with damaged cord or plug. If unit is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to your authorized service dealer for repair. S Avoid unintentional starting of the unit. Never carry unit with you

S When not in use, the unit should be stored in a dry, high or locked-up place out of the reach of children. S When storing unit, unplug and use a bar sheath. TRANSPORTING AND STORAGE S Stop the unit and disconnect the power source when not in use. S Carry the unit with motor stopped. S Store unit indoors in a high, dry place out of the reach of children. Store unit unplugged. S Do not hang unit so that the trigger switch is depressed. SAFETY NOTICE: Exposure to vibrations through prolonged use

(Apply grease on smooth side of handle lock to aid in keeping lock in place until handle assembly is lowered into position.) Grasp handle assembly. Hold in “up” position. Be sure handle lock remains in gearcase notch. Slide handle assembly into position. Rotate handle assembly down. Insert rear carriage bolt first, with bolt head on L.H. side of tiller and loosely assemble locknut (See Fig. 5). Insert pivot bolt in front part of plate and tighten. Cut down remaining corners of carton and lay

#10-24 17 102604X Grip, Bar Control 4 126949X428 Bracket, Handle 18 150696 Bolt, Pivot 5 72110514 Bolt, Carriage 5/16-18x1-3/4 21 145829 Bar, Controi 6 108281X Rod, Shift 22 150744 Grip, Handle 7 72110608 Bolt, Carriage 3/8-16 x 1 Gr. 5 24 73731000 Nut, Keps #10-24 UNC 8 4497H Clip, Hairpin 25 127012X Control, Throttle 9 109229X Lock, Handle 26 146480 Grommet, Handle 10 73930600 Nut 3/8-16 27 10040500 Washer, Lock 5/16 11 19131611 Washer 13/32x1 x 11 Ga. 28 73800500 Locknut 5/16-18 12 1

This Warranty does not apply to any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product. 5. Exclusions: Excluded from this Warranty are belts, tines, tine adapters, normal wear, normal adjustments, standard hardware and normal maintenance. 6. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer. Should you have any unanswered questions conce

• Rotate tiller handle to the right and pull tiller out of carton. CHECK TIRE PRESSURE The tires on your unit were overinflated at the factory for shipping purposes. Correct and equal tire pressure is important for best tilling performance. • Reduce tire pressure to 20 PSI (1.4 kg/cm2). HANDLE HEIGHT • Handle height may be adjusted to better suit operator. (See “TO ADJUST HANDLE HEIGHT” in the Service and Adjustments section of this manual). 6 OPERATION KNOW YOUR TILLER READ THIS OWNER'S MANUAL

H. 3 8393J 21546828 Pin, Stake, Depth 4 12000035 21546055 Ring, Klip 5 180847 21546218 Bolt, Carriage, Gr. 5 5/16-18 x 3/4 6 8394J 21546829 Spring 7 8392J 21546827 Bracket, Latch 8 109230X 21546043 Spring, Depth Stake 9 188862X422 21546271 Shield, Tine 13 72110510 21546763 Bolt, Carriage 5/16-18 x 1-1/4 14 124343X 21546075 Bracket, Shield Tine 15 161414X422 21546146 Shield, Side, Outer RH 16 73900400 21546788 Nut, Hex Flange 1/4-20 unc 18 72040410 21546758 Bolt, Carriage 1/4-20 x 1-1/4 Gr. 5 19

N Limpie regularmente el orificio de entrada de aceite (1), el conducto de aceite (2) y la ranura de la espada (3). N Mida la profundidad de la ranura, con el calibrador de rectificacion (accesorio especial), en la zona utilizada para la mayoria de los cortes. Picco 3/8 pulg P 5,0 mm (0,20 pulg) Rapid 1/4" 4,0 mm (0,16 pulg) Si la profundidad de la ranura es menor que la especificada: N Sustituya la espada. De lo contrario las pestanas de los eslabones impulsores rasparan la parte inferior de la