Make sure WHITE FOAM GASKET (5) is under flange of DRAIN BODY (4). Fig. B. Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (6) must face towards the rear of the SINK. Fig. B. Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3). Fig. A. 2 REAR OF SINK 4 5 6 3 1 SINK DRAIN HOLE FLAT SIDE OF GASKET MUST FACE DOWN 1 2 Fig. A. 2 1 FLAT SIDE OF GRAY LOCKNUT MUST FACE UP INSTALL GRAY LOCKNUT 5 Install GRAY LOCKNUT (1) onto DRAIN BODY (2) fro

Place it in the sink outlet. From under the sink, install the black mack gasket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time. Thread the tee and tailpiece to the flange. The pivot must face the faucet. If necessary, turn the drain assembly. Tighten the retainer nut. Place the plunger assembly in the drain. Install the horizontal rod so that the end goes through the loop in the bottom of the height adjuster. Install and ha

Install the spout. Rotate the spout escutcheon if necessary, so that the hole for the pull rod is at the rear. Tighten the mounting nut. Tighten the tensioning screws. Screw the connecting hoses into the spout tee. Slide the 3/8" compression nuts and ferrules over the ends of the hoses. Connect the hoses to the valve outlets. Use two wrenches so that the hoses do not twist or become loosened from the spout tee. Install the supply lines (not included). Install the drain. Turn on the water and che

Model CP43D2001 is cost down solution. * All readings are typical values. * Specifications are subject to change without notice. 23 http://www.deltaww.c<

for CP43D2001) Specifications Model No. Working Voltage (V) Rated Voltage (V) Max Water Head m-H.O Max Flow Rate ml/min Weight (gw) Operation Temperature Noise dB(A) MTBF (hour) CP43A2003 6-13 12.0 1.8 1750 50 5°C - 65°C 23 44,000at 35°C CP43D2001 6-13 12.0 1.7 1650 50 5°C - 60°C 25 30,000at 35°C *Noise Measurement Condition: 25 cm above Pump ( Pump is filled with Pure Water) * Model CP43D2001 is cost down solution. * All readings are typical values. * Specifications are subject

• Detergentes que contienen acido fosforico tampoco pueden ser aplicados ilimitadamente. • Por regla general no se deben mezclar detergentes. • Tampoco se deben utilizar utensilios abrasivos, como son polvos abrasivos, esponjas o panos de microfibra. • Si tienen que seguir siempre las instrucciones de uso de los fabricantes de los detergentes. • La limpieza tiene que ser realizada segun la dosificacion y el tiempo de actuacion, en funcion del objeto y ajustada a las necesidades especificas del m

ounted Available Finishes Chrome Brushed Nickel The measurements shown are for reference only. Products and specifications shown are subject to change without notice. Specification sheet revised 4/2008 AXOR' 41534001 41534821

This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. WHAT IS COVERED BY THE WARRANTY This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or workmanship as follows: Hansgrohe will repair at no charge for parts onl