Averiguar que la palanca y la boca sean alineadas adecuadamente hacia adelante. 6. Apretar la mondana de laton (4) con la llave dotada o utilizar los adecuados instrumentos. NOTA: INSTALACION SOBRE SUPERFICIES SOLIDAS: la parte de abajo al plan de apoyo tiene que ser llana y falto de virutas; en caso contrario el mezclador no podra ser colocado adecuadamente en la misma sede. INSTALACION SOBRE BALDOSAS: Evitar l’ instalacion del mezclador cerca de o sobre las fugas. El mezclador podria no result

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-1600 Series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Inlet connections: 1/2. NPSM Please read our instruction before you

Sacar todos los elementos necesarios por el montaje de la bollita de plastico 3. Insertar el O-ring grande en el tallo del mezclador y colocar el mezclador donde deseado NOTA: El O-ring de goma tiene que ser insertado entre el plan de montaje y el cuerpo del mezclador. No utilices mastique, u otro sellador, en este punto. 4. Instalar a los miembros de montaje (GR0356031) sobre el tallo fileteado en la secuencia aquii bajo indicada: 1 – mondana plana rotonda en fibra Respaldo perfilado triangular

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet FF-3000 series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Tailpipe connections: 3/8. O.D. Please read our instruction before

FFP S700 SERIES Pull-Out Spray Faucet Installation guide ENGLISH 2 G 1748.XX G 1782 G 1156 G 29016 G R0239.XX G 13396.XX G R0637 G R1664 G 1636 G 1463 TECHNICAL DATA · Minimum working pressure 0,5 bar · Maximum working pressure 5 bar · Recommended working pressure 3 bar (in case of water pressure higher than 5 bar it is recommended to install pressure reducers) · Maximum working temperature 70°C PARTS LIST G 13396.XX Handle G R0239.XX Ring cap G 1156 Cartridge G R0637 Fastening set (rubber washe

These include pre-filter and carbon cartridges. Filter cartridges are easily replaced by removing the stainless steel cartridge housing’s cap. This automatically shuts off the water supply and allows the new cartridge to be inserted quickly and cleanly. It is recommended that a new cartridge is used every 6-12 months according to water quality. Any noticeable reduction in the filtered water’s flow rate usually indicates a new cartridge is required. Franke Uniftow and Little Butler™ Systems wor

Proceed with the following steps: Step 1: Verify that the line and load cables comply with applicable electrical codes. Step 2: Verify that the transfer switch rated current and voltage (see identification plate on the door of the transfer switch) agree with system current and voltage. Step 3: After the transfer switch is mounted, provide the conduit or cable openings as required. Ensure that no metal filings contaminate the transfer switch components. Step 4: Test all power cables before connec

(215) 822-6590 Kitchen Systems Division Telefax (215) 822-5873 Suite 500 3050 Campus Drive/Hatfield, PA 19440 Distributed by: Kindred Industries Limited Tel. 1-866-6FRANKE 1000 Kindred Road Tel. 1-866-527-5145 Midland, Ontario L4R 4K9 Installation instructions and warranty for Franke faucet PF-1000 and PF-2000 series Technical data Maximum water pressure: 75 PSI Maximum hot water temperature: 175° F Recommended hot water temperature: 150° F Connection: 1/2. NPT Please read our instruction before