Indica una situacion potencialmente peligrosa, la cual, si no es evitada, podria resultar en lesiones menores o m o d e - r a d a s . Usado sin el simbolo de seguridad de alerta indica una situa-cion potencialmente riesgosa la que, si no es evitada, podria causar danos en la pro p i e d a d . PROPOSICION DE CALIFORNIA 65 Algunas particulas originadas al lijar, aserrar, amolar, taladrar y realizar otras actividades de construccion contienen productos quimicos que producen cancer, defectos de naci

HERRAMIENTAS DE ENSAMBLAJE REQUERIDAS 1/8" Llave Inglesa Hexagonal (suministro) El Destornillador de Phillips 6 Mm Llave Inglesa Hexagonal (suministro) la Llave Inglesa Ajustable ESTIMACION DEL TIEMPO DE ENSAMBLAJE Menos de 1 hora AJUSTANDO LA TENSION DE CORREA Su lijadora se envia de fabrica con la correa de marcha (A) Fig. 2 ensamblada a ambas poleas (B) y (C). Antes de ensamblar la unidad de disco a la maquina, revise y ajuste la tension de correa: 1. Afloje el tornillo (D) Fig. 1 con la 6 Mm

#JB11085 printEd in taiWan .........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

-30 G0449/G0450 37" Drum Sander To adjust V-belt tension: 1. Disconnect power to the sander! 2. Open the side cover. 3. Turn the motor mount nuts in the direction shown in Figure 30 to loosen or tighten the V-belts. - - - - Pulley Alignment Pulley alignment is another important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplaner) for optimum performance. Each pulley can be adjusted by loosening the set screw that secures the pu

4. Motor overloaded. 1. Repair or replace connections on motor for loose or shorted terminals or worn insulation. 2. Correct the low voltage conditions. 3. Install correct fuses or circuit breakers. 4. Reduce load on motor. Drums run backwards (G0450 only). 1. Two of the power wires are reversed (G0450 only). 1. Switch two of the current carrying wires at the main power block (G0450 only). Machine slows when sanding, making a squealing noise, especially on start-up. 1. V-belts loose. 2. V-belts

WASHR 3/8 (G0582/G0445) 5318 P05825318 HANDLE (G0582/G0445) 5319 PSS08 SET SCREW 5/16-18 X 1/2 5320 P05825320 ADJUSTMENT RING (G0582/G0445) 5321 PB03 HEX BOLT 5/16-18 X 1 (G0582/G0445) 5322 PW07 FLAT WASHER 5/16 (G0582/G0445) 5323 P05825323 HANDLE (G0582/G0445) 5401 P05825401 HOUSING (G0582/G0445) 5401 P9962Z5401 HOUSING (G9962Z/G9962ZX) 5402 P05825402 ROLLER (G0582/G0445) 5402 P9962Z5402 ROLLER (G9962Z/G9962ZX) 5403 P9962Z5403 FASTENING TUBE 5405 P05825405 PULLEY (G0582/G0445) 5405

Keep loose clothing rolled up and long hair tied up and away from machinery. Table Movement Adjusting Feed Rate T able height can be adjusted manually or with the digital key pad and motor (see Figure 15). Manual Table Movement: Turn the handwheel located under the front of the infeed table for manual table positioning. Motorized Table Movement: Press the TABLE UP or TABLE DOWN key once for motorized table positioning in 0.005" (0.1mm) increments. Numerical Key Pad: Push the keys to enter

3. Replace conveyor belt. Straight strip of notches on workpiece. 1. Pressure rollers are dirty or damaged. 1. Clean or repair pressure rollers. Awarning For your safety, turn the power switch off and disconnect the sander from the power source and the air supply before starting the applicable troubleshooting. -40- o G0445/G0582/G9962Z/9962ZX Wide Belt Sander Troubleshooting SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Snake shaped marks on workpiece. 1. Sanding belt damaged or dirty. 1. Cl

Improper oscillation. To check the sanding belt oscillation: 1. Be sure the sanding belt is properly installed and the belt tension knob and air supply are ON. 2. Turn ON the sanding belt. —If the belt oscillates without contacting the limit switches, but the oscillation time to the left and right are NOT equal, proceed to Step 7, on Page 31. 3. An adequate stream of air through the air fork gap (Figure 26) is essential for proper oscillation. If the jet of air is weak through the gap, the

Simbolos La etiqueta de su herramienta puede incluir los siguientes simbolos. V....................voltios A .................amperios Hz..................hertz W.................vatios min.................minutos ................corriente alternante ............corriente directa no ................velocidad sin carga .................Construccion Clase II ...............terminal a tierra ................simbolo de alerta .../min ........ .revoluciones u de seguridad oscilaciones por minuto Cabl