Do not put any objects like sticks or fingers in holes of impeller cover. 4. Stop the engine and disconnect the spark plug wire before attempting to clean obstructions or blockage from the intake or discharge passages. 5. Stop the engine and allow it to cool for at least two minutes before refilling the gas tank or before lifting leaf blower. 6. Do not put a vacuum kit of any kind on this machine. Foreign objects entering the impeller housing will destroy the impeller and may cause injury. M

Note that there are three holes in each side of the upper handle. These are height adjustment holes. Position the upper handle at a comfortable height for you (usually waist high). Move the upper handle up or down slightly to align the hole in the upper handle and lower handle. Locate the upper lifting handle (item 4) and with the hardware provided, bolt through the upper lifting handle, lower and upper handle. Tighten securely. 3. Attach the throttle control to the upper handle as per the draw

091-0058 SNAPPER * 1189 Old Schuylkill Road * P.O. Box 111 * Parker Ford, PA 19457-0111 PHONE: (215) 495-7181 * * * FAX: (215) 495-5951 Form SLB862 693 LEAF BLOWER OWNER’S MANUAL Assembly Instructions Your leaf blower has been carefully packed at the factory. Before proceeding with assembly, make sure all parts have been received and are in good condition. If there are shortages or damage, report it immediately to the company from whom you obtained the machine. (Note: In the following In

Shaft Key Engine Housing 5/16-24 x 3/4" HHCS Pltd 5/16" Split Lockwasher Pltd Impeller 3/8-24 x 1-1/4" HHCS Pltd Housing Spacer Front Housing 5/16-18 x 5/8" HHCS Pltd 5/16-18x1-1/2" HHCS Pltd Impeller Cover Chute Weld Assembly Diverter Weld Assembly 3/8" Internal Lockwasher Pltd. Vinyl Grip, Diverter Handle Diverter Clip 1/4-20 x 1/2" HHCS Pltd 1/4" Split Lockwasher Pltd 1/4" Flat Washer Pltd Spring, Diverter 1/4-20 x 5" Lg. Carriage Bolt 1/4-20 x 6" Lg. Carriage Bolt Defle

Box 111 * Parker Ford, PA 19457-0111 Phone: (610) 495-7181 or (800) 348-1117, Fax: (610) 495-5951 McDonough, GA., 30253 U.S.A. COPYRIGHT ©1999 SNAPPER INC. ALL RIGHTS RESERVED MANUAL No. 0-6168 (f.R. 08/02/99) MANUAL No. 06168 2 LEAF BLOWER PART NO. Item No. SLB552PN PART NO. SLB862IC Quantity Description 1 705-0088 2 703-0108 3 090-0457 4 705-0028-2 5 090-0091 6 705-0044 7 705-0034 8 705-0002 9 090-0057 10 703-0422 11 090-0031 12 703-0415 13A 090-0090 13B 14 703-0424

Hinge & Deflector (Deflector Removed for Clarity) D. Tapered Spacer E. Original Lockwasher and Nut F. 5/8 x 1 Cylinder Spacer A BC Figure 7. Connect Deflector Spring A. Spring Anchor B. Spring C. Deflector Arm 6 7 54”Turbo Blower Installation Instructions FRONT Install Turbo Blower 1. Install the turbo blower assembly. Insert the tapered spacers (B, Figure 8) through the bottom of the blower housing (A). 2. Install one spring clip (C) on both tapered spacers (B). 3. Hook the bottom of the turbo

• To remove turbo, reverse the installation steps. Recommended Accessories • Front counterweight is recommended when using rear-mounted grass catcher. • On slopes over 17.6% (10°), use two rear wheel weights in addition to front counterweight. Always mow up and down the face of slopes, never across the face. Never mow on slopes greater than 30% (16.7 degrees) NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position. 1 2 Installation Instructions 54”Turb

Make sure the blower end is directed away from people, animals, glass, and solid objects. - -- For Parts Call K&T 606-678-9623 or 606-561-4983 BlowerVacuumSTARTINGPOSITION WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property,

• Never attempt to make major repairs on this unit unless you have been properly trained. Improper service procedures can result in hazardous operation, equipment damage and voiding of manufacturer’s warranty. 4 3 unit assembly Note: Please refer to Parts List for correct part identification and placement. FRONT WHEEL ASSEMBLY • Attach left and right caster brackets to caster wheel using 3/8-18 x 2-1/4 bolt and lock nut. Insert bolt through hole in bracket. Place caster wheel onto bolt. Place ot

Be sure all safety features are attached, adjusted properly and functioning properly. • Never operate with the discharge deflectors removed or altered. • Do not change the engine governor setting or over speed the engine. • Stop on level ground, shut off engine before leaving the operator’s position for any reason. • Stop equipment and inspect impeller blades after striking objects or abnormal vibration occurs. Make necessary repairs before resuming operations. • Keep hands and feet away intake