2. Insert safety ignition key. 3. Fill fuel tank. 4. Move throttle to FAST position. 5. Move to FULL position. 6. Prime as instructed in the Operation section of this manual. 7. Wait a few minutes before restarting, DO NOT prime. 8. Connect wire to spark plug. 9. Replace spark plug. 10. Drain fuel tank and carburetor, refill tank with fresh gasoline. 11. Drain fuel tank and carburetor, refill tank with fresh gas o line. Loss of power 1. Spark plug wire loose. 2. Throwing too much snow. 3. Fuel t

inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 21 22 REPAIR PARTS SNOW THROWER - MODEL PR524 (96192001501) CONTROL PANEL / DISCHARGE CHUTE 1 2 6 7 4 5 6 8 8 19 2 2 26 28 27 27 25 20 29 3 18 17 10 15 12 21 9 16 14 13 31 34 30 33 REPAIR PARTS SNOW THROWER - MODEL PR524 (96192001501) CONTROL PANEL / DISCHARGE CHUTE KEY PART NO. NO. DESCRIPTION 1 414280 Knob

PR8527ES (96192001701) AUGER HOUSING / IMPELLER ASSEMBLY KEY PART NO. NO. DESCRIPTION 4 191079 Pulley, Impeller 5 188909 Bearing Assembly, Flange 6 155377 Nut, Hex Flange 5/16-18 7 180355 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 72270505 Bolt, Carriage 5/16-18 x 5/8 9 163183 Nut, Cage 3/8-16 404929X428 Housing, Auger 11 404932X428 Bar, Scraper 12 178675X008 Bracket, Corner Discharge 13 175322 Base, Discharge Chute 14 10040500 Washer, Lock 5/16 15 19111507 Washer, Flat 16 74940516 Screw, Hex Hea

Wipe up any spilled gasoline. 2. REMOVE DISCHARGE CHUTE - Loosen locknut se cur ing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and dis charge chute to be removed from snow thrower. 3. REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual. 4. REMOVE ENGINE PULLEY - Remove bolt, lock wash er and flat washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crank shaft. 5. SEPARATE SNOW THROWER - Wi

Water in engine can result in shortened engine life. 14 15 CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower. 4. Connect spark plug wire to spark plug. Replace safety ignition key. WARNING: To avoid serious injury, before performing any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key. 3. Make sure the augers and all mov ing parts have completely stopped. 4. Remove safety ignition key

6. Regular la altura de la maquina quitanieves para evitar areas de gravilla o de pedrisco. 7. No intentar nunca hacer regulaciones mientras el motor este en marcha (excepto cuando esta recomendado especificamente por el fabricante). 8. Llevar siempre gafas de proteccion o mascaras para los ojos durante la utilizacion de la maquina o mientras se haga una regulacion o una reparacion para proteger los ojos de objetos extranos que pueden ser lanzados por la maquina quitanieves. Funcionamiento 1. No

• Follow a regular schedule in maintaining, caring for and using your snow thrower. • Follow the instructions under “Maintenance” and “Storage” sec tions of this own er’s manual. TABLE OF CONTENTS SAFETY RULES ........................................................2-3 MAINTENANCE .....................................................14-15 PRODUCT SPECIFICATIONS ......................................3 SERVICE AND AD JUST MENTS ...........................16-18 CUSTOMER RESPONSIBILITIES ...........

25 26 REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001900) DRIVE 4 4 4 4 4 2 2 43 11 1 1 5 22 5 5 2 2 20 41 21 17 13 3 6 14 19 18 18 15 24 36 35 34 37 31 9 12 23 26 29 25 4 4 28 33 32 27 44 REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001900) DRIVE KEY PART NO. NO. DESCRIPTION 1 401619 Chain, Drive 2 751153 Nut, Lock 5/16-18 3 402882 Clip, Retainer 4 17490508 Bolt, Hex Head 5/16-18 x 1/2 5 408981 Bearing, Flange 6 12000007 E-Ring, Retainer 9 402855 Sprocket & Shaft Assembly 11 402568 R

1. Move choke to OFF position. runs roughly 2. Blockage in fuel line. 3. Stale fuel. 4. Water in fuel. 5. Carburetor is in need of adjustment or overhaul. 2. Clean fuel line. 3. Drain tank and refill with fresh, clean fuel. 4. Drain fuel tank and carburetor, refill tank with fresh gasoline. 5. Contact a qualified service centre. Excessive vibration 1. Loose parts or damaged augers or impeller. 1. Tighten all fasteners. Replace damaged parts. If vibration remains, contact a qualified service cent

414643 Rev 3 12.07.07 TH Printed in the U.S.A. IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. Look for this symbol to point out impor tant safety precautions. It means CAUTION!!! BE COME ALERT!!! YOUR SAFE TY IS IN VOLVED. WARNING: Always remove safety ignition key and disconnect spark plug wire. Place it where it c