WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. McDonough Power Equipment McDonough.GA« 30253 A FUOUA MDUBTMEB Company Manual 06012 (l-4257)Rev. 1, 11/10/00 Printed in U.S.A. INDEX - MAIN CONPONENTS SUBJECT PAGE(S) Arm, Idler................... ............3.1-3.2 Assembly, Gear Box.......... ............1.2-1.3 Assembly, Spindle........... ...............3.3 Augers...

Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA MANUFACTURING, INC. © Copyright Simplicity Manufacturing, 2007 Inc. All Rights Reserved. Printed In USA. TP 400-4575-00-AT-SMA Mfg. No. Description Attachment 1694543 Wide Body Cart Collector Hitch & Tube Kit Part No.: 1734881 Table Of Contents s PRODUCT COMPONENTS PAGES Hitch & Tube Group ............................................................................................................................................. Torqu

Kit Parts Ref. Description Qty. A. Searing 8. Nut. 3/8 C. Lockwasher. 3/8 D. Lift Arm E. Nut, Centerlock F. Trunnion, Rear G. Lift Rod H. Washer, 1 I. Lift Shaft J. Capscrew, 3/8-16 X 1 K. Capscrew, 5/16 L. Lockwasher, 5/1 6 M, Nut, 5/16 N. CaiviCraw-.7/1 8-1 4x 1-1/2 0. Upstop Plate P. Lockwasher, 7/16 Cl. Nut, 7/16 R. Capscrew, 7/16-14x 1-1/4 S. Lockwasher, 7/16 T. Nut. 7/16 U. Capscrew, 1/2-13 x 1-1/4 V. Lockwasher. 1/2 W. Nut, 1/2 X. Hitch Y. Trunnion, Front Z. Washer A

Refer to FIG. 3.5 and 3.6. 3.4 Section III ■ MAINTENANCE SKID SHOE ADJUSTMENT The skid shoes should be lowered to raise the blower housing to clear gravelled or rough surfaces. If necessary, adjust up until almost even with the edges of the housing, to effectively clear smooth paved surfaces. Note that the skid shoes can be installed upside down to track better over icy or hardpaced surfaces. To adjust the skid shoes, place a wood block under the lower edge of the blower housing. Loosen the

Keep in mind that it, like any other mechanical device, can be potentially dangerous if used improperly and that no accident prevention program can be successful without the wholehearted cooperation of the person responsible for the operation of the equipment. Study this Operator's Manual carefully to learn about operation of all controls and pay particular attention to the Important Safety Precautions on Page 2. Following these instructions will help you continue to enjoy the trouble-free opera

Keep in mind that it, like any other mechanical device, can be potentially dangerous if used impiroperly and that no accident prevention program can be successful without the wholehearted co- TWO STAGE THROWERS operation of the person responsible for the operation of the equipment. Study this Operator’s Manual carefully to learn about operation of all controls and pay particular attention to the Important Safety Precautions on Page 2. Following these instructions will help you continue to enj

Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug. PROBLEM POSSIBLE CAUSE REMEDY Engine fails to start. 1. Key is OFF. 1. Push key in to the ON position. 2. Failure to prime cold engine 2. Press primer button twice and restart. 3. Fuel valve is in CLOSED position. 3. Turn valve to OPEN position. 4. Out of fuel. 4. Fill fuel tank. 5. Choke OFF - cold engine. 5. Turn choke to ON, set throttle to FAST. 6. Engine flooded. 6. Turn choke to OF

5. To lower the height of the scraper bar, raise the skid shoes. 6. If the scraper bar becomes worn, it can be replaced by removing the hardware attaching it to the snowthrower. A B Figure 3. Chute Deflector Adjustment (Some Models) A. Chute Deflector Knob B. Chute Deflector Figure 5. Skid Shoe Adjustment A. Scraper Bar B. Skid Shoe C. Nuts Figure 4. Remote Deflector Control (Some Models) A. Maximum Throwing Position B. Spring C. Control Handle C A A B C B 13 Operation FULL TRACTION Easy Turn™ L

7006160 Copyright © 2006 Briggs & Startton Corporation Milwaukee, WI USA. All Rights Reserved Revision IR, 12/4/2006 TP 400-5246-IR-LF-N Table Of Contents s PAGE GROUP 4 Handle & Controls Group 8 Auger Drive Group 10 Gear Box Assembly 12 Auger Housing & Chute Group 16 Engine & Frame Group 20 Traction Drive Group 24 Wheels & Tires Group 26 Decal Group TWO STAGE LARGE FRAME Manual No. 7006160 SERIES 8 TP 400-5246-IR-LF-N 3 Handle & Controls Group Manual No. 7006160 TWO STAGE LARGE FRAME TP 400-524

23 1923282 2 CAPSCREW, Hex Head, 1/4-20 x 2-1/2 G5 Used on 38” models 24 1960346 4 CAPSCREW, Hex Head, 1/4-20 x 2-1/4 G5 Quantity 4 used on 38” models 25 1668344 2 PIN, Flat Head Drilled 26 1918447 2 PIN, Cotter 47/50 x 3/4 27 1718782A 1 AUGER ASSEMBLY, L.H. 9-1/2 LG Used on 24” models 27 1718784A 1 AUGER ASSEMBLY, L.H. 11-1/2 LG Used on 28” models 27 1718786A 1 AUGER ASSEMBLY, L.H. 13-1/2 LG Used on 32” models 27 1723945A 1 AUGER ASSEMBLY, L.H. 15-9/10 LG (without Bushing) Used on 38” models 27