7/16" 3 658468 7 Carriage bolt 5/16" NC x 5/8" 3 O/L 8 Machine screw 10-32 NC x 5/8" 3 2700008 9 Nylon insert locknut 5/16" NC 2 O/L 10 Nylon insert locknut 5mm x 0.8 3 1000020 11 Decal "Warning" 1 660988 12 Decal "Danger" 1 657761 13 Hex. bolt 1/4" NC x 1/2" NC Gr.5 6 O/L 14 Serrated flange nut 1/4" NC 6 O/L 15 Flatwasher 1/4" 3 O/L O/L = Obtain Locally DR® SNOW THROWER Safety, Operation & Maintenance Instructions PARTS Manual chute rotation system REF DESCRIPTION QTY PART # 1 Rotation handle 1

7. Do not attempt to operate on steep slopes or near embankments. 8. Use extra caution when backing up. 9. Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protection such as earmuffs or earplugs to protect your valuable hearing. 10. Always wear eye protection during operation (safety goggles, face shield, etc.). 11. Never allow anyone to operate the equipment until they read the manual completely and are thoroughly familiar with basic DR® ALL-TER

Read and understand this manual before operation. This manual has been prepared to assist the owner/operators in the safe operation and suitable maintenance of the DR® SNOW THROWER. The information was applicable to products at the time of manufacture and does not include modifications made afterwards. Read and understand this operator's manual before attempting to put a DR® SNOW THROWER into service. Familiarize yourself with the operating instructions and all the safety recommendations contain

Torque Pounds-Foot Newtons-MeterTorque Pounds-Foot Newtons-MeterTorque Pounds-Foot Newtons-Meter BOLT SIZES Inches Millimeters MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. 1/4 6.35 5 6 6.8 8.13 9 11.0 12.2 14.9 12 15 16.3 30.3 5/16 7.94 10 12 13.6 16.3 17 20.5 23.1 27.8 24 29 32.5 39.3 3/8 9.53 20 23 27.1 31.2 35 42.0 47.5 57.0 45 54 61.0 73.2 7/16 11.11 25 30 40.7 47.4 54 64.0 73.2 86.8 70 84 94.9 113.9 1/2 12.70 45 52 61.0 70.5 80 96.0 108.5 130.2 110 132 149.2 179.0 9/16 14.29

Reference numbers are used in the illustrations. These numbers correspond to those in the “Reference Number” (REF) column, and are followed by the description and quantity required. O/L - “Obtain Locally” in the part number column indicates common hardware that is available at your local hardware supply. All reference to right and left, forward or rearward, are from the operator steering the DR® ALLTERRAIN ™ MOWER. The manufacturer reserves the rights to change, modify, or eliminate from time to

Where it is possible to throw the snow to the left and right (above), as on a long driveway, it is advantageous to start in the middle. Plow from one end to the other, throwing snow to both sides without changing the direction of the discharge chute. If the snow can only be thrown to one side of the driveway or sidewalk (above), start on the opposite side. At the end of the first pass, rotate the discharge chute 180 degrees for the return pass. At the end of each succeeding pass, rotate the disc

! WARNING: Always keep the DR® SNOW THROWER discharge away from people, animals and objects which could be struck by debris. Adjustments Deflector Adjustment Adjust the deflector angle according to the distance the snow must be thrown. To adjust, loosen the knob, adjust to the desired angle then tighten knob securely. Skid Shoe Adjustment (Figures 8 & 9) Adjust skid shoes in order to allow the required clearance (H) between the cutting edge and the surface, by loosening the 5/16" x 5/8" carriage

1. Place the chute (item 1) on the discharge hole (item 2) around the DR® SNOW THROWER. 2. Install the three retaining plates (item 3) using the six 1/4" x 1/2" bolts and flange nuts (items 4-5), tighten securely. Verify that the chute turns freely on the collar. Figure 2 DR® SNOW THROWER Safety, Operation & Maintenance Instructions ASSEMBLY & INSTALLATION ! WARNING: Before installing the DR® SNOW THROWER, always bring the DR® ALLTERRAIN ™ MOWER to a complete stop, shut off the engine and remove

2015280 and up OM 0308 TABLE OF CONTENTS INTRODUCTION – TO THE PURCHASER..........................................................................................................4 SAFETY PRECAUTIONS.......................................................................................................................................5 Before Operation .................................................................................................................................................5 N