NOTE: DO NOT use primer to restart a warm engine after a short shutdown. NOTE: Additional priming may be necessary if the temperature is below 15° Fahrenheit. 3. Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil. 4. Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. 5.

Refer to page 11 for instructions on how to properly use it. NOTE: This item is fastened with a cable tie to the rear of the auger housing at the factory. Cut the cable tie before operating the snow thrower. WARNING: Never use your hands to clean snow and ice from the chute assembly or auger housing. Lamp Wiring Harness (If equipped) The post on the cable tie attaching the lamp wiring harness to the lower handle should be plugged into the hole in the lower handle. Pull the slack portion of the w

Damage resulting from the installation or use of any part, accessory or attachment not approved by Cub Cadet for use with the product(s) covered by this manual will void your warranty as to any resulting damage. Normal wear parts are warranted to be free from defects in material and workmanship for a period of thirty (30) days from the date of purchase. Normal wear parts include, but are not limited to items such as: batteries, belts, blades, blade adapters, grass bags, rider deck wheels, seats,

60 Ottawa Street South, KITCHENER, ONTARIO N2G 4J1 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION OPERATOR’S MANUAL 06/10/08 769-04103 28”, 30”, 33” & 45” Two-Stage Snow Throwers This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Table of Contents Safety Symbols................................................... 3 Maintaining Your Sn

Fold fastener back and under the side chain as pictured below. You will probably need pliers to do it. Once both fasteners are connected, chain assembly must be snug on tire. Advance fasteners on each side chain the same number of links until chain is sufficiently and evenly tight on tire. See front cover picture for proper chain fit. Remove or tie down all unused links once chain is satisfactorily tight. 5 Repeat previous steps for other tire. To get maximum wear and years of use from your

Ignition Key The ignition key is a safety devise. It must be fully inserted in order for the engine to start. Remove the ignition key when the snow thrower is not in use. Important: Do not turn the ignition key in an attempt to start the engine. Doing so may cause it to break. Figure 4-1 Drive Control Headlight Oil Fill Fuel Cap Primer Choke Ignition Key Oil Drain Starter Button Electric Starter Outlet Recoil Starter Handle Chute Assembly Clean-Out Tool Auger Control Shift Lever Two-Way Chute Co

Doing so will cause premature wear on the drive system’s friction wheel. WARNING The muffler, engine, and surrounding areas become hot and can cause a burn. Do not touch. 4 Operating Your Snow Thrower NOTE: Use slower speeds in higher snow and/or until you are familiar with the snow thrower operation. IMPORTANT NEVER move the shift lever without first releasing the wheel drive control. Doing so will cause premature wear on the drive system’s friction wheel. Stopping The Engine Run engine for a f

No. Part No. Description 33 731-0846C Upper Chute 34 714-0104 Pin, Internal Cotter Pin 35 710-04187 Hi-Lo Screw, 1/4-15 x 0.5 36 684-04230 2-Way Chute Control™ Assy 37 731-04954 Steering Control 38 710-04326 Screw, #8-16 x 0.50 39 732-04219A Clutch Lock Spring 40 720-0201A Knob, Crank 41 735-0234 Grommet, Rubber 42 720-04072 Knob, Star, 5/16-18 43 731-04785 Handle Clutch Lock - LH 44 684-04105A Handle Engage Assy - LH 45 784-5594 Cable Bracket 46 747-04263 Eye Bolt 47 736-0231 Flat Washer 48 712

If the engine falters, quickly rotate the choke control back toward FULL choke, and then slowly into the OFF position again. 6. When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower. Recoil Starter 1. Rotate choke control to FULL choke position (cold engine start). NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL. 2. Push the primer two or three times for col

Do not touch. • For the most efficient snow removal, remove snow immediately after it falls. • Discharge the snow downwind whenever possible. • Slightly overlap each previous path. • Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock. • Be certain to follow the precautions found in the To Stop Engine section to prevent