DO NOT USE IT ON STAIRS, ESCALATORS OR OTHER UNEVEN SURFACES. NEVER USE IT WITH INLINE OR ROLLER SKATES. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN CAUSE AN ACCIDENT RESULTING IN SERIOUS INJURY. Bolt Bushing figure 3: To adjust stroller wheel tracking Installing Cover 1. At top of trailer frame, fit openings on cover sides around handle bar mounts. Fasten small buckle sections together. Adjust as needed. Photo 12 2. On trailer sides, join buckle sections on rear cover corners to buckle sections be

Repeat for the other wheel. Note: wheels are not centered on the axle. Make sure wheels are held securely, with wheel shaft fully inserted into the hollow axle. You should not be able to rock or shift wheels. Improp- erly installed wheels can fall off, causing an accident or serious injury. WARNING A B C Mounts horizontally to frame Quick-release lever in locked “Closed” position Quick-release lever in unlocked “Open” position Installing and Operating the Tongue d’Lite™, Encore™, Solo™, Lady Bug

For questions and additional information, contact your authorized Burley dealer or visit burley.com. Box Contents: 1 tote bag, 1 manual, 1 warranty card, 1 hex key ( 4mm ), 2 tie-down straps, 1 hitch, 2 wheels, 1 trailer Required Tools: 4mm Hex key (included) Burley Travoy Guide 1. Flex Connector 7. Tow Bar 2. Upper Frame Hinge 8. Light Mount 3. Twist Grips 9. Upper Frame k. Middle Frame Hinge 10. Lower Frame 5. Tie-Down Buttons 11. Shelf 6. Push-Button Wheel 12. Kickstand Unfolding

^i«c # ÉÉ I

• Practice with your child in an uncongested area. Pulling the trailercycle adds length and weight to your bicycle; allow for ample time and distance to stop, start, and turn. • Take short rides; stop frequently. Instruct your child to keep their feet on pedals and hands on handlebars at all times. • Recommended speed limits: 15mph (24km/h) on smooth, straight roads 5mph (8km/h) when turning or on uneven roads • Do noT exceed weight limit by attaching a rack, panniers, or other cargo to the trai

Every effort has been made to ensure your purchase is a top-quality, thoroughly-tested design, ready to provide many years and miles of happy, safe trailering. Please go to or contact us at burley@burley. com to register your warranty information. IMPORTANT IT IS VERY IMPORTANT FOR YOU TO FAMILIARIZE YOURSELF WITH YOUR BURLEY BY READING THIS ENTIRE MANUAL BEFORE USE. IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT YOUR AUTHORIZED BURLEY DEALER OR VISIT WWW.BURLEY.COM. Introduction Once you’ve done the

If you have any questions about using your QR axle, please consult your bicycle manual or Burley dealer. Install the standard hitch (included with your Burley trailer) onto the Adapter and secure with the provided nut. Tighten to 20 N-m (15 ft-lb). It may be necessary to grip the knurled portion of the Adapter with pliers while tightening the nut. Refer to your Burley trailer manual for information on using your Burley hitch. Solid Axle Adapter Installation Remove non-drive (left) side axle

2. Position top of rack parallel to the ground. Check distance from stay mounting hole on Moose Rack to the bicycle’s seat stays. Figure 1 BA Figure 1: The difference between heights A & B must be less than 3/4” (19.05 mm) rACK MuSt Be LeVeL. WheN PuLLiNg A trAiLerCYCLe, A NoN-LeVeL rACK CAN ADVerSeLY AFFeCt BiCYCLe hANDLiNg, reSuLtiNg iN AN ACCiDeNt or SeriouS iNJurY. WArNiNg 3. Adjust rack stays to fit. Photo 1 Moose Rack Instructions Contents: (2) Band Clamps (4) M5 Socket Head Screws (4) Was

5. Open retaining pin and insert through hitch and flex connector holes. Rotate and close spring clip. 6. Tighten and close quick release lever, with lever pointing to rear of bike. A properly adjusted quick release lever should leave an imprint on your palm when the lever is rotated to the closed position. 7. Wrap safety strap twice around chain stay and then over hitch body. Fasten hook to D-ring on underside of tow bar end. 8. To remove trailer from bicycle, unfasten clip from D-ring and remo

7. Using two screwdrivers, one inside the bucket and one outside, tighten the mounting screws firmly, until the spring washers are fully flattened between the mounting screw heads and fender washers. 8. Take care to keep the far left post from rotating as you tighten its mounting screw so that the brake return spring does not distort. Flag Handlebar Flag Installation Hole Handlebar Installation Rollbar Accessory (optional) Knob Using the Parking Brake For All Trailers Except the Bee™ Engage the