FEATURES • Attractive white finish • Vertical louvers - disperse heat evenly • Front-mounted, snap action, bimetallic thermostat (Model 112 only) • Heavy-duty, steel sheathed, plate-finned element • Factory-wired for 240 VAC, 1500W • Field-convertible to operate on 120 VAC, 750 or 1500W • Mounts into standard kickspaces beneath cabinets, vanities, counters, stairways, etc. ACCESSORIES (purchase separately) • Model 86W Line-Voltage Thermostat • Model 59W / 59V 60 Minute Timer • Model 6

It is therefore very important to carefully read all the operating instructions, recommendations and warnings prior to installation and use of the appliance. Note in particular the text paragraphs with the danger triangle design, to avoid damages to persons or objects. Keep this instruction booklet in a safe place: this booklet should always accompany the appliance at such time as it is sold or given to other persons for use. Installation and service • Any electrical installation of the cooker h

AEG - putting words into action. Introduction The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (special accessory). The unit features two outlet holes, one of which A is located on the top of the unit while the other B is located on the rear. To connect up the hose, you should first fit the bayonet-mounting flange C on the outlet required (if using the top outlet, fix the flange in place using the screw supplied as s

Al cortar o perforar la pared o cielo raso, no dane el alambrado electrico ni otras instalaciones no visibles. 6. No instale la unidad encima de una banera o ducha. 7. NUNCA coloque un interruptor en un lugar que pueda ser alcanzado desde una banera o ducha. 8. No haga funcionar esta unidad con un variador de luz o control de velocidad. 9. SOLAMENTE MODELO 161: Instale la caja a no menos de 16 cm de la pared lateral. Para conexiones de alimentacion, use un alambre apropiado para un minimo de 75

Lea las instrucciones de “ADVERTENCIA” y “CUIDADO” que aparecen arriba. MODELOS 162 & 164 SOLAMENTE: LA UNIDAD FUNCIONARA EN FORMA MAS EFICIENTE SI SE UBICA EN UN LUGAR DONDE SE MINIMICE EL TENDIDO DE CONDUCTOS Y EL NUMERO DE CODOS. LAS UNIDADES HAN SIDO DISENADAS PARA USO CON CONDUCTO REDONDO ESTANDAR DE 10 cm. Note que las unidades de dos bombillas (163 & 164) pueden montarse con una bombilla infrarroja (para la calefaccion) y una bombilla reflectora (para la luz). Se pueden usar controles dob

MODEL / MODELO 161 • Clave la unidad a las vigas. • Fije los conductos (modelos 162 o 164 solamente). • Connect power cable. • Conecte el cable de potencia. • Fasten grille to housing. WHITE to WHITE BLANCO a BLANCO • Fije la rejilla a la caja. PREPARE THE HEATER BLACK to BLACK PREPARACION DEL CALENTADOR 1. Remove the unit from carton. Save carton for use as plaster shield in rough-in installations. 2. Slide adjustable mounting brackets into bracket channels on housing. (Fig. 2) WHITE to WHITE B

Las partes 3) de abajo de los soportes deben colocarse a nivel con la 3. Brackets are factory-set for ." thick ceiling material. For thicker ceilings, loosen 4 vertical adjusting screws and lower housing to appropriate thickness on gauges. Tighten vertical adjusting screws firmly. (Fig. 4) 120 VAC LINE IN LINEA DE ENTRADA 120 VCA BLACK NEGRO parte de abajo de la viga. (Fig. 3) 3. Los soportes se fijan en fabrica para material de cielo raso de un grosor de 1,3 cm. Para cielo raso mas gruesos, afl

Follow the instructions for operating the hood to recirculate air. • When the temperature outdoors becomes more mild (spring), the filter can be removed and the hood converted once again for to extraction. Please consult the assembly instructions for operating the hood in extraction mode. 5 Electrical connection 220-240 V - using fixed power supply line with plug. (The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the us