3. Remove depth gauge tool. With flat file, round off front corner of cutter depth gauge (see Figure 22). After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing. Flat File Depth Gauge Slot Depth Gauge Tool Depth Gauge Figure 21 - Depth Gauge Tool On Chain Front Corner .025" Figure 22 - Round Off Front Corner Of Depth Gauge REPLACING SAW CHAIN Replace chain when cutters are too worn to sharpen or when chain breaks. Only

Let the engine cool down sitting on concrete, metal, bare ground or solid wood (e.g. the trunk of a felled tree) away from any combustible substances. Warning! To reduce the risk of fire or burn injury, let the unit cool down before refueling your chainsaw after use. Warning! Never disassemble or modify your muffler. The muffler could be damaged and cause an increase in heat radiation or sparks, thereby increasing the risk of fire or burn injury. You may also permanently damage the engine. H

This rule applies also for those compact saws designed for use in confined spaces. Position the chain saw in such a way that your body is clear of the cutting attachment whenever the engine is running. Stand to the left of the plane of the cutting attachment. A Warning! Do not operate your chain saw with the starting throttle lock engaged. Cutting with the starting throttle lock engaged does not permit the operator proper control of the saw or chain speed. Begin cutting with the saw at full

maam ST/HL021.023.025 Instruction Manual iwner’s Manual Manual de instrucciones Manual del usuario ...» Warning! Read and follow all safety precautions in Owner’s Manual - improper use can cause serious or fatal injury. To reduce the risk of kickback injury use STIHL reduced kickback bar and STIHL PM 1 f/s" Picco) or RM 2 (0.325") chain depending on sprocket pitch or other available low kickback components. ©Andreas Stihl 1993 Advertencia! Lea y siga todas las precauciones de seguridad

If the grip droops to one side: Increase spring tension by one additional turn. 46 021,023, 025 Checking and Replacing Chain Sprocket • When starter rope is fully extended it must be possible to rotate the rotor at least another half turn. if this is not the possible, the spring is over-tensioned and could break. • Take off one turn of the rope. • Fit the fan housing on the engine housing. • Set the Master Control lever to ©t Replacing a broken rewind spring • Lubricate the new spring

If the chain is run dry, the whole cutting attachment will be irretrievably damaged within a very short time. Always check chain lubrication and oil level in tank before starting work. • Every new chain has to be broken in for about 2 to 3 minutes. • After breaking in chain, check chain tension and adjust if necessary -see section "Checking chain tension". 38 021, 023, 025 During Break-in Period During Operation A factory new machine should not be run at high revs (full throttle off loa

1 Assembly Chainsaw assembly and preparation ..............................… 2 Compatible chainsaws and sprockets ……………………… 2 RIPSAW assembly ….........................................................…. 3 Dimension plate assembly …........................................…. 4 Guide beam assembly.......................................….……… 5 End clamp assembly …………………………………………….. 6 Blades Changing blades …..............................................……….. 11 Tracking blades Drive wheel …………………………

Re-install cover knobs and tighten securely. 10. Tighten the tension bolt until the indicator reaches the white line. Refer to chainsaw owner’s manual for the proper oil/gasoline ratio. Maintain an ample supply of bar and chain oil in the reservoir to lubricate the drive mechanism of the RIPSAW. 3 Dimension plate assembly Figure 1. Dimension plate assembly 1. Remove dimension plate and parts from box. 2. Slide guide arm under handle bracket with square pin facing downward. 3. Install and tighten

Puede no satisfacer las exigencias de ANSI si se la utiliza con otras sierras. Cadena serrada (Cadena) Una cadena cerrada que tiene eslabones dentados para cortar madera. El motor impulsa la cadena y la barra de guia la sostiene. Contragolpe Movimiento rapido hacia arriba y hacia atras de la barra de guia. Los contragolpes pueden producirse cuando el extremo de la barra de guia toca algun objeto mientras la cadena se halla en movimiento. La barra de guia se sacude hacia arriba y hacia atras, en

Some states do not allow limitation of how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation of damages may not apply to you. This warranty provides the original purchaser with specific rights. For information regarding those rights, please consult the applicable state laws. Industries of Canada, Inc. 2220 Argentia Road Unit #4 Mississauga, Ontario INTERNATIONAL L5N 2K7 P.O. Box 90004 905-826-8010 Bowling Green, KY 42102-