Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death. BOLT TORQUE Mounting procedures for mowers will require a significant amount of bolt nut and washer installation. Frame and structure mounting bolts should be installed using Red Loct

(SRM-1) 12.3 Engaging the Power Take Off (PTO) Before engaging the PTO, make certain that the area is clear of bystanders and passersby. The implement must be completely lowered and the deck positioned at a safe operating height. NEVER engage the PTO with the implement in the raised position. Set the tractor engine speed at approximately 1,000 RPM before engaging the PTO. Shift the PTO control to the on position, and slowly increase the engine speed until the PTO is operating at the rated speed.

(Figure ASM-R-0151) ASSEMBLY © 2006 Alamo Group Inc. ASSEMBLY A96B 03/06 Assembly Section 3-13 CHAIN GUARD (EXTRA EQUIPMENT) CHAIN GUARDS: Front and Rear Chain Guards (Optional Equipment) are recommended for higher than normal usage (100 hours or more per year) and will provide protection from thrown objects with careful operation. Chain Guards must be maintained in good repair by replacing missing or worn sections or by being replaced when seriously worn or damaged. Front Chain Guards 1. Attach

OPS-R-0004_F OPERATION © 2009 Alamo Group Inc. OPERATION RX60/72/84 03/09 Operation Section 4-19 Shorten the driveline profiles as follows: • Remove the driveline from the tractor. • Raise and lower the mower to find the position with the shortest distance between the tractor PTO shaft and cutter gearbox. Shut down the tractor and securely block the mower in this position. • Pull driveline apart and reattach yoke to PTO shaft. • Hold driveline sections parallel to one another and measure back 1”

Parts Section -144 MOUNTING COMPONENTS - COMMON BOX (PART 2) Machete Boom 17 21 and 24 04-04 Rev 12-08 ©2008 Alamo Group Inc. Parts Section -145 MOUNTING COMPONENTS - COMMON BOX (PART 2) Continued... ITEM PART NO. QTY. DESCRIPTION 35 02968156 1 HOSE, SWING CYL BASE (GREEN W/ WHITE STRIPE TIE) 36 02973297* 1 HARDWARE KIT (* INCLUDES ALL THE FOLLOWING ITEMS) * 00001300 2 LOCKWASHER (IN ITEM 36) 00001800 8 LOCKNUT (IN ITEM 36) 00002700 10 FLATWASHER (IN ITEM 36) 00011100 4 FLATWASHER (IN ITEM 36) 0

Parts Section -16 HYD CYL ASY - BAR TILT - PN 0693500A ITEM PART NO. QTY. DESCRIPTION 0693500A 1 BAR LIFT CYLINDER ASY. 1 02977114 1 TUBE WLD’MT 2 02977116 1 CYL HEAD 3 02977115 1 ROD WLD’MT 4 --------------1 * O-RING 5 --------------1 * BACK-UP SEAL RING 6 --------------1 * ROD SEAL 7 --------------1 * ROD WIPER 8 --------------1 * WIRE RING 9 02977121 1 SEAL KIT, ( * INCLUDES ITEMS 4, 5, 6, 7 & 8 ) Switchblade 5`and 6` Spring-Brk-a-way (11-06) Rev 08-11 ©2011 Alamo Group Inc. Parts Section -17

BEFORE YOU START!!Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. In order to reduce accidents and enhance the safe operation of mowers,

21 50 IN ROTARY - BLADE PAN ASY......................................................................................................................................................... 23 60 IN ROTARY - BLADE BAR ASY......................................................................................................................................................... 24 60 IN ROTARY - HEAD ASY (SOLID MNT)............................................................................................

Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety Messages before assembling, operating or servicing this Implement. This equipment should only be operated

Estas parte s son echa s y pr oba das a la especificaciones de RHINO. Partes que no son autenticas no regularmente llegan co n es tas es pecificaci ones. El uso de partes que no son au tenticas puede reducir el funcionamiento de la cortadora, anular garantias, y presentar un peligro de seguridad. Use pa rtes de cortadora autenticas de RHINO por economia y seguridad. (SPRM-1 SP) CONTACTE A SU D ISTRIB UIDOR RHINO SEGURIDAD © 201.. Alamo Group Inc. SEGURIDAD 260/272/284 01/11 Seccion de Seguridad