Tighten securely. BAGGER KIT INSTALLATION STEP 11: Install bumper mount standoffs onto rear bumper of machine, utilizing existing hardware on machine. NOTE: Invert hardware when installing standoffs, installing bolts out through bumper with nuts facing out. NOTE: When installing standoffs, be sure that the bumper mount plate mounting holes along the back bar of the standoffs are located towards the right side of the machine. Refer to the Parts List section of the manual. STEP 12: Install bumper

Figure 11. Tension Springs A. Eyebolt D. Pivot Frame B. Nut, 5/16 E. Nut, 5/16 C. Spring B D C A E Figure 12. Spring Assist Bracket A. Spring Assist Bracket B. Capscrew, 1/2-13 x 1-1/4 C. Lockwasher, 1/2 D. Hex Nut, 1/2-13 E. Hitch 11 Initial Setup & Assembly 2. Increase front tire pressure to 20 psi (138 kPa) to compensate for added weight of the hitch, plus bar and blade. Be sure both tires have equal pressure. 3. From the front of tractor, slide the hitch under the tractor so that the hitch b

Note: The lid screen can be partially removed for easier cleaning and should be cleaned regularly. The blower housing and tube should be removed for cleaning. Inspect the grass bags for wear or damage. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. STORING THE GRASS CATCHER CAUTION Do not leave grass in bagger containers. Empty containers after each use and before storing. Failure to do so may result in spontaneous combustion which could de

No. Description 1694542 Wide Body Cart Grass Catcher (Multiple Applications) 1726564 Revision 01 Rev. Date 07/2004 TP 100-4002-01-AT-UV Table of Contents Contents, Accessories, & Specs Table of Contents.............................................1 Recommended Accessories............................1 Specifications ..................................................1 Safety Rules & Information General Warnings............................................2 Safety Decals ............................

Install Spacers 1. Install the rear spacers (C, Figure 3). Secure with two 1/2-13 x 2-1/2 capscrews (E), washers (D), spacers (C), and 1/2-13 nylock nuts (A) per side. A C D D B Figure 3. Install Rear Spacers A. Nylock Nuts, 1/2-13 C. Spacers B. 1/2-13 x 2-1/2 Capscrew D. 1/2” Washers 4 Initial Assembly & Installation Figure 4. Upright Identification Use this upright with Broadmoor / 1600 / 2600 / LT Series Use this upright with Prestige / 1800 / 2800 / YT & Conquest / 1700 / 2700 / GT Series Fi

HARDWARE REFERENCE Tools Required for Assembly: * 7/16" wrench * 1/2" wrench * Flat Head Screwdriver * Hammer * Pair pliers L-1782-BH-01 3. Parts Reference Parts List L-1782-BH-01 4. REF. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 22 23 25 26 27 28 29 30 31 32 33 PART NO. B-983 B-1673P C-123 R-618 R-635-01 R-636 R-637-01 R-640 R-653 R-704 R-705-10 R-713-10 R-746 R-755-10 R-1503 R-1835-10 R-2466-10 R-2474-10 R-2473-10 R-775-10 R-803 10M0840P 11M1016P 30M1000P 40M1000P 45M1111P 45M1717P R

Use a block of wood to prevent blade rotation while loosening the capscrew. 5. Reinstall the large washer (B, Figure 5), spring washer (C) and capscrew (D). Use a wooden block (A) to prevent blade rotation while tightening the capscrew (D) to 45-55 ft. lbs. (61-75 Nm). LOOSENA Figure 4. Blade Removal A. Blade A B C D Figure 5. Blade Installation Mowers A. 4x4 Wood Block B. Hex Washer C. Spring Washer D. Blade Capscrew 5 Puck Installation A C F G D D E Figure 6. Install Pin and Bracket A. Lower C

Personal bodily injury can result when these instructions are not followed. The information is for your safety and it is important! The safety decals below are on your product. If any decals are lost or damaged, replace them at once. See your local dealer for replacements. TP 600-2562-01-AT-SMA These labels are easily applied and will act as a constant visual reminder to you, and others who may use the equipment, to follow the safety instructions necessary for safe, effective operation. Attachme

When cleaning snow from gravel or earth drives or walks, the shoe assemblies should be lowered fully to prevent blade contact with gravel or ground. When cleaning smooth hard surfaces like concrete, the shoe assemblies are normally placed fully up to allow the blade to scrape the surface. To adjust the skid, raise the blade off the ground and block with a piece of wood. Loosen the bolts (B, Figure 3) and move the skid shoes (A) up or down to desired height. Tighten the bolts securely. Figure 3.

No. Description 1693754 42” Remote Angling Snow Plow/Dozer Blade Hitch Mfg. No. Description 1693757 Hitch (for Sovereign / 900 / 2800 Series) 1721303-01 Rev 1/2001 TP 100-2374-01-AT-SMA Table of Contents Recommended Accessories ..............................1 Safety Rules & Information General Warnings............................................2 Operating on Slopes........................................2 Preparation ......................................................2 Operating Safety......