POLY PRO DROP SPREADER OWNERS MANUAL Model No. 45-02881 ™ • Safety • Assembly • Operation • Maintenance • Parts CAUTION: Read Rules for Safe Operation and Instructions Carefully 175 LB. POLY PRO DROP SPREADER OWNERS MANUAL Model No. 45-02881 ™ the fastest way to purchase parts PRINTED IN U.S.A. FORM NO. 47717 (REV. 8/06) RULES FOR SAFE OPERATIONS Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all ti

Outside the tank, assemble the nylon washer, then the nylon nut onto the drain body. Tighten the nut securely enough to prevent leaking, being careful not to damage the plastic parts. Place the O-ring inside the nylon cap and screw the cap onto the end of the drain body. See figure 4. NYLON NUT O-RING NYLON CAP HOSE GASKET DRAIN BODY NYLON WASHER FIGURE 4 9. Assemble the boom mount bracket to the rear of the hitch tubes using two 5/16" x 2" hex bolts and 5/16" hex nuts. See figure 5. BOOM MOUNT

Tenga siempre cuidado cuando usa un equipo motriz. 1. Lea este manual del propietario con mucho cuidado antes de tratar de armar u operar este rociador. 2. Lea el manual del propietario de su vehiculo y todas las reglas de seguridad antes de usar este equipo. 3. Nunca permita que los ninos operen este rociador ni permita tampoco que personas adultas operen el equipo sin las instrucciones necesarias. 4. No permita que nadie se monte ni se siente sobre este rociador. No permita tampoco que nadie s

El extractor de paja de 40" se muestra en las ilustraciones. El procedimiento de ensamble es igual para el extractor de paja de 48". 1. Ensamble la placa elevadora al tope del protector de la horquilla usando cuatro pernos hexagonales de 5/16" x 3/4" y contratuerca hexagonal de 5/16" segun se muestra en la figura 1. Ajuste. 2. Invierta el protector de la horquilla. Vea la figura 2. 3. Ensamble dos (altos) soportes de montaje del brazo del enganche y dos soportes (cortos) angulares a los orificio

10. Instale la lengueta en la bandeja, colocando hacia el frente la muesca que se traba en la ranura. Use dos tornillos hexagonales de 3/8" x 1" (D), dos tornillos hexagonales de 3/8" x 1-1/4" (C), cuatro espaciadores de 1/4" de largo (P) y cuatro tuercas hexagonales de presion de 3/8" (J) como se muestra en la figura 7. Apriete todos los herrajes. 11. Instale dos tornillos hexagonales de 3/8" x 1-1/4" (C), cuatro espaciadores de 1/4" de largo (P) y dos tuercas hexagonales de presion de 3/8" (J)

45-0299 48" PLUG AERATOR CAUTION: Read Rules for Safe Operation and Instructions Carefully Assembly Operation Maintenance Repair Parts thefastest way to purchase parts PRINTED IN USA FORM NO. 48309 (4/25/07) RULES FOR SAFE OPERATIONS Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. CAUTION: VEHICLE BRAKING AND STABILITY MAY BE AFFECTED WITH THE ADDITION OF AN ACCESSORY OR AN ATTACHMENT. BE AWARE OF CHANGING CON

PULLEY CLUTCH LEVER PLUNGER REAR DRIVE.. COVER FOUR.. SCREWS CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clu

FORM NO. 49464 (5/04) CAUTION: Read Rules for Safe Operation and Instructions Carefully • Safety • Assembly • Operation • Maintenance • Parts the fastest way to purchase parts Agri-Fab. TABLE OF CONTENTS SAFETY RULES ...................................................... 3,4 SAFETY AND OPERATIONAL DECALS ................ 5,6 HARDWARE CHART .................................................. 7 ASSEMBLY ............................................................ 8-11 OPERATION.....................